Switchgear & Substations

Resistor Symbol & Basic Component Symbols: Circuit Guide

Resistors, capacitors, inductors and transistors representing each resistor symbol and component symbol

Key takeaways

  • A resistor is a zigzag in IEEE 315 drawings and a rectangle in IEC 60617 drawings; both add a diagonal arrow to show a variable resistor.
  • In a battery symbol the longer thin line is the positive terminal and the shorter thick line is negative, with several pairs drawn for multi-cell batteries.
  • Inductor symbols show the core: no lines for air core, two solid parallel lines for an iron core and dashed lines for a ferrite core.
  • IEC 60417 separates earth (5017), protective earth (5019) and frame or chassis (5020), which matters when reading switchgear and control drawings.
  • An LED on 24 V DC with 2 V forward drop at 10 mA needs R = (24 − 2) / 0.01 = 2.2 kΩ and dissipates 0.22 W.

Quick answer: The resistor symbol is a zigzag line in IEEE 315 (ANSI) drawings and a plain rectangle in IEC 60617 drawings, with an arrow added for variable resistors. Other basic symbols: a capacitor is two parallel plates, an inductor a row of loops, a battery long and short parallel lines, ground three shortening horizontal lines, and a bipolar transistor a base bar with collector and arrowed emitter.

Every schematic, from a PCB in a protection relay to the trip circuit of a medium-voltage breaker, is built from a small vocabulary of passive and active components. Resistors, capacitors, inductors, batteries, ground connections and semiconductors appear on nearly every sheet, and their symbols are the first thing an engineer learns to read.

This guide is for students, technicians and engineers who need a reliable reference for these basic electrical and electronic symbols in both IEEE 315 and IEC 60617 forms. It also explains the symbol for current and why it is I, and works through two short calculations that connect the symbols to real component ratings.

What Does a Resistor Symbol Look Like?

A resistor is a component that opposes current flow and converts electrical energy to heat in proportion to P = I² × R. Its symbol is the clearest indicator of which drawing standard a schematic follows.

Resistor typeIEEE 315 / ANSIIEC 60617
Fixed resistorZigzag line, typically three peaks on each side, between two leadsPlain open rectangle, about three times as long as wide
Variable resistor (rheostat)Zigzag with a diagonal arrow drawn through itRectangle with a diagonal arrow through it
PotentiometerZigzag with an arrow pointing at its side (the wiper), three terminalsRectangle with an arrow pointing at its side
Preset (trimmer)Zigzag with a diagonal line ending in a short barRectangle with a diagonal ending in a bar
ThermistorZigzag or rectangle with a diagonal line that has a short horizontal tail, marked T or θRectangle with tailed diagonal and θ
Varistor (VDR)Rectangle or zigzag with a tailed diagonal marked U or VRectangle with tailed diagonal and U
Heating elementZigzag or rectangle labeled HTRRectangle with internal hatching or label

The resistor schematic symbol is labeled with a designator (R1, R2) and value. In switchgear control circuits, resistors appear in trip circuit supervision relays, in space heaters inside panels, and as current-limiting resistors in indicator lamps.

For the rest of the symbol family, see our electrical symbols chart.

Capacitor Circuit Symbol and Variants

A capacitor is a component that stores energy in an electric field between two conductive plates separated by a dielectric. The symbol mimics that construction.

  • Non-polarized capacitor: two equal straight parallel lines with a narrow gap, leads attached at the middle of each. Same in IEEE and IEC.
  • Polarized (electrolytic) capacitor, IEEE: one straight plate and one curved plate; the curved plate is negative, and a + sign marks the straight plate.
  • Polarized capacitor, IEC: one open (outline) rectangle plate and one filled rectangle plate, or two straight lines with a + sign; the filled plate is negative.
  • Variable capacitor: the basic symbol with a diagonal arrow through it; a trimmer uses a diagonal ending in a bar.

Capacitor values are written as C1 100 nF or C3 470 µF 63 V; for electrolytics the voltage rating is as important as capacitance. In power systems the same plate symbol appears at much larger scale: power factor correction banks in LV switchboards and MV capacitor banks in substations are drawn with the capacitor symbol on the single-line diagram, rated in kvar rather than farads.

Capacitive reactance links the symbol to circuit behavior: Xc = 1 / (2πfC). A 100 µF capacitor at 50 Hz has Xc = 1 / (2 × 3.1416 × 50 × 0.0001) ≈ 31.8 Ω. Power factor and the role of capacitors in correcting it are explained in the power factor guide.

Inductor Schematic Symbol: Air Core, Iron Core and Variable

An inductor is a coil of wire that stores energy in a magnetic field and opposes changes in current. The electrical coil symbol is a row of loops or half-circles, and lines drawn alongside it describe the core.

SymbolHow it is drawnMeaning
Air core inductor symbolRow of three or four loops (IEEE) or half-circles (IEC), no core linesCoil with no magnetic core; low inductance, linear
Iron core inductor symbolSame coil with two solid parallel lines beside itLaminated steel core; high inductance, can saturate
Ferrite core inductorCoil with two dashed parallel linesFerrite or powdered core, used at higher frequencies
Variable inductor symbolCoil with a diagonal arrow through itAdjustable inductance
Adjustable coreCoil with core line and arrow on the coreInductance tuned by moving the core
Older IEC inductorFilled (solid black) rectangleInductor, found on older European drawings
Tapped inductorCoil with a lead taken from between loopsIntermediate connection

The inductance symbol in equations is L, measured in henries. Inductive reactance is XL = 2πfL, so a 10 mH choke at 60 Hz presents XL = 2 × 3.1416 × 60 × 0.010 ≈ 3.77 Ω.

The inductor core lines are the same convention used in transformer symbols: two coils with solid lines between them mean an iron-core transformer. Our iron core transformer symbol guide builds on this, and inductor vs transformer explains how the two devices differ in function.

Battery Symbol in a Circuit and DC Sources

A battery is one or more electrochemical cells connected to supply DC voltage. The battery electrical symbol is built from cell symbols.

  • Single cell: one long thin line and one short thick line in parallel. The long line is positive, the short line negative.
  • Battery of cells: several cell pairs in a row, or two pairs joined by a dashed line to indicate many cells, with the overall voltage written beside it, for example 110 V DC.
  • Battery with tap: a lead brought out between cells.
  • DC voltage source (ideal): a circle with + and − marks, or a circle with a line along the lead direction in IEC style.

The schematic symbol of a battery is the same in IEEE 315 and IEC 60617, which makes it one of the few truly universal symbols. On a battery electronic symbol in PCB schematics, a coin cell is drawn as a single cell; on substation drawings, the station battery that supplies protection and breaker tripping is drawn as a multi-cell symbol feeding the DC distribution board.

Battery voltage drives the equations: cells in series add voltage, cells in parallel add capacity. Twelve 2 V lead-acid cells give 24 V; a 110 V DC station battery is typically made up of about 52 to 55 lead-acid cells, depending on the float voltage and design. Large DC systems for substations and energy storage are covered in the stationary battery systems guide.

Ground Symbols: Earth, Chassis and Signal Ground

Ground schematic symbols look similar but mean different things, and mixing them up can create noise problems in electronics or safety problems in power equipment.

SymbolHow it is drawnMeaningIEC 60417 ref.
Earth (ground), generalVertical lead ending in three horizontal lines decreasing in lengthConnection to earth5017
Protective earthEarth symbol enclosed in a circlePE terminal for safety bonding5019
Frame or chassisHorizontal line with three short diagonal strokes below it (rake shape)Connection to equipment frame5020
Functional / noiseless earthEarth symbol with a semicircle or shield around itDedicated clean earth for electronics5018
Signal or common groundOpen downward-pointing triangleCircuit reference (0 V), not necessarily earthedCommon practice
Equipotential bondingTwo lines joined with a short stub, or earth symbol with additional markBonding between conductive parts5021

The earth wiring symbol in a wiring diagram is the PE conductor drawn as a line ending in the protective earth symbol, with conductor color green/yellow under IEC rules or green or bare in North America. On a ground circuit symbol in a power schematic, the earth symbol at a transformer neutral shows a solidly grounded system; a resistor between neutral and earth shows resistance grounding.

Sizing the equipment grounding conductor drawn by these symbols is covered in the equipment grounding conductor sizing guide.

Transistor Symbols and Other Semiconductor Symbols

Transistor symbols are largely the same in IEEE and IEC practice, which simplifies reading electronics schematics from any source.

  • NPN bipolar transistor: a vertical bar (base) with a lead from the left; two diagonal lines from the bar, the collector without an arrow and the emitter with an arrow pointing out of the device.
  • PNP transistor: the same, with the emitter arrow pointing in toward the base.
  • N-channel MOSFET: gate line separated from the channel by a gap (insulated gate), with source, drain and an arrow on the body pointing in toward the channel; enhancement types draw the channel as three short segments.
  • P-channel MOSFET: the same with the arrow pointing out.
  • IGBT: insulated gate like a MOSFET, with collector and arrowed emitter like a bipolar transistor; used in drives, inverters and energy storage PCS.
  • Diode: triangle pointing toward a bar; current flows in the direction of the triangle, the bar marks the cathode.
  • Zener diode: as diode, with bent ends on the bar. LED: diode with two outward arrows. Thyristor (SCR): diode with a gate lead at the cathode.

A transistor electrical symbol is labeled Q1, Q2 (or V and T in some IEC drawings), with type number or ratings in the parts list. In power conversion equipment, the same IGBT and diode symbols are drawn in bridge arrangements; the power conversion system guide shows how they form the inverter in a battery energy storage system.

Symbol for Current: What Does I Stand For in Electricity?

The symbol for current is I, from the French intensité du courant (current intensity), the term used by André-Marie Ampère, after whom the unit, the ampere (A), is named. Voltage uses V or U (U is preferred in IEC and European texts), resistance R, and power P.

On drawings, current is shown in several ways:

  • An arrow alongside a conductor labeled I or with a value, showing the assumed direction of conventional current (positive to negative).
  • An ammeter: a circle with the letter A, connected in series.
  • An ideal current source: a circle with an arrow inside in IEEE and textbook practice; IEC 60617 draws a circle with a line perpendicular to the leads, while an ideal voltage source has the line along the leads.
  • A current transformer on a power line: a small circle or coil with its ratio.

Worked example: sizing an LED indicator resistor

A green LED indicator on a 24 V DC control panel, forward voltage 2.0 V, target current 10 mA. Using Ohm's law:

R = (Vs − Vf) / I = (24 − 2.0) / 0.010 = 2,200 Ω = 2.2 kΩ

P = I² × R = (0.010)² × 2,200 = 0.22 W

Choose a 2.2 kΩ resistor rated at least 0.5 W for margin. The Ohm's law guide covers related formulas, and reading these values off a full schematic is explained in how to read electrical drawings.

Next Steps: Where Component Symbols Meet Switchgear Specification

Basic component symbols are not only for electronics. Switchgear and substation drawings use them throughout the secondary circuits: resistors for trip circuit supervision and anti-condensation heaters, capacitors for capacitor trip units and power factor correction, inductors for reactors, batteries for the DC auxiliary supply, and ground symbols for every bonding point.

When reviewing supplier drawings for switchgear:

  • Confirm the symbol standard and that the legend defines every component used.
  • Check heater and thermostat ratings and supply voltage in each panel.
  • Verify the DC auxiliary voltage and battery capacity assumed for tripping and closing.
  • Confirm PE and functional earth connections are drawn and terminated as separate symbols where required.

MARS supplies KYN28 metal-clad switchgear, SF6 ring main units and IEC 61439 LV boards with full schematics, and every unit is routine tested before shipment. See the HV and LV switchgear range and request drawings or a proposal through the quote request form.

Frequently asked questions

What is the symbol of a resistor?

A resistor is drawn as a zigzag line in IEEE 315 and ANSI drawings and as a plain rectangle in IEC 60617 drawings. Both standards add a diagonal arrow through the symbol for a variable resistor, and an arrow pointing to the side for a potentiometer wiper. The designator R1, R2 and the value are written beside it.

Which side of the battery symbol is positive?

In a battery or cell symbol the longer, thinner line is the positive terminal and the shorter, thicker line is the negative terminal. A battery of several cells repeats the long and short pair, and the total voltage is usually written beside the symbol. This convention is the same in IEEE 315 and IEC 60617.

What is the difference between earth ground and chassis ground symbols?

Earth ground is drawn as three horizontal lines of decreasing length and means a connection to the earth electrode system. Chassis or frame ground is a horizontal line with short diagonal strokes beneath it and means a connection to the equipment enclosure. Signal ground, an open triangle, is a circuit reference that may not be earthed.

How do you tell an iron core inductor from an air core inductor symbol?

An air core inductor symbol is a row of loops or half-circles with nothing beside it. An iron core inductor adds two solid parallel lines alongside the coil to represent the laminated core. Dashed parallel lines indicate a ferrite or powdered iron core, and a diagonal arrow through the coil indicates a variable inductor.

Why is current represented by I?

Current is represented by I from the French phrase intensité du courant, meaning current intensity, used by André-Marie Ampère in his early work on electrodynamics. The unit of current, the ampere, is named after him. Standard formulas such as Ohm's law, V = I × R, use I for current in all major standards.

What does the transistor symbol arrow mean?

The arrow on a bipolar transistor symbol is on the emitter and shows the direction of conventional current. In an NPN transistor it points out of the device; in a PNP transistor it points in toward the base. On MOSFET symbols the arrow is on the body connection and indicates N-channel when pointing in.

Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .

Tags: resistor symbol battery symbol circuit ground schematic symbol capacitor circuit symbol inductor schematic symbol

More guides