Switchgear & Substations

Electrical Symbols: Chart of IEEE and IEC Diagram Symbols

Printed electrical drawings with electrical symbols on an engineer's desk with scale ruler

Key takeaways

  • Two symbol standards dominate: IEEE 315, also published as ANSI Y32.2, in North America, and the IEC 60617 database used in Europe, Asia and most export projects.
  • A resistor is a zigzag line under IEEE 315 but a plain rectangle under IEC 60617, which is the quickest way to tell which convention a schematic uses.
  • A solid dot at crossing conductors means a connection; a plain crossing means no connection, and IEC practice prefers offset T-junctions to avoid ambiguity.
  • Direct current is marked with a solid line over a dashed line (IEC 60417-5031) and alternating current with a tilde (IEC 60417-5032).
  • Single-line diagrams represent all three phases with one line, using IEC double-circle or IEEE coil symbols for transformers and squares or switch shapes for breakers.

Quick answer: Electrical symbols are standardized graphic marks that represent components such as wires, power sources, switches, fuses, breakers, lamps, transformers and ground on circuit, wiring, one-line and plan drawings. North American drawings follow IEEE 315 (ANSI Y32.2); most other countries use IEC 60617. Always read the drawing legend first, because projects may mix conventions or add their own symbols.

A drawing set is only as clear as its symbols. An electrician reading a panel schedule, a commissioning engineer tracing a trip circuit and a buyer checking a switchgear single-line diagram all depend on the same graphic language, and misreading one symbol can mean a wrongly wired interlock or a breaker ordered at the wrong rating.

This guide is the starting point of our electrical symbol series. It explains the two main standards, gives an electrical symbols chart for the most common circuit, wiring, schematic and one-line diagram symbols, and links to detailed guides on outlets, lighting, breakers and fuses, switches and relays, motor control and basic components. Symbols are described in words and tables so you can match them to any drawing.

What Are Electrical Symbols and Which Standards Define Them?

Electrical symbols are simplified graphic representations of electrical components and connections, defined by standards so that any trained reader can interpret a drawing without seeing the physical equipment. They appear on several kinds of electrical drawings: schematics, wiring diagrams, one-line diagrams, panel layouts and architectural electrical plans.

The main symbol standards

  • IEEE 315 / ANSI Y32.2 (with CSA Z99 in Canada): graphic symbols for electrical and electronics diagrams, the basis of most North American schematics and one-line diagrams.
  • IEC 60617: an online database of graphical symbols for diagrams, adopted in Europe as EN 60617 and used for IEC-based projects worldwide. It replaced the older multi-part paper editions.
  • IEC 60417: symbols for marking equipment, such as the AC and DC signs, protective earth and on/off markings printed on nameplates.
  • NEMA ICS and JIC conventions: ladder-diagram practice for industrial control in North America.
  • Architectural plan symbols: historically ANSI Y32.9, now usually defined by each firm's legend in line with industry practice.

IEEE and IEC symbols for wires, ground and switches look broadly similar, but resistors, fuses, lamps, contacts and coils differ enough to cause mistakes. Electrical electronics symbols for semiconductors are closer between the two. When a drawing package comes from an overseas supplier, expect IEC symbols and IEC device designations such as -Q1 or -F2 rather than CB1 or FU2. Our guide on how to read electrical drawings explains how legends, reference designators and cross-references tie the symbols together.

Electrical Symbols Chart: IEEE 315 vs IEC 60617

The chart below compares the circuit symbols that most often differ between North American and IEC drawings. Each description tells you how the symbol is drawn.

ComponentIEEE 315 / ANSI Y32.2IEC 60617Meaning
ResistorZigzag line, usually three peaks each sidePlain rectangle, about 3:1 length to widthFixed resistance
FuseS-shaped curve, or rectangle with line throughRectangle with a line running its full lengthOvercurrent element that melts
Circuit breaker (schematic)Open contact with a curved arc over itSwitch contact with a small cross (x) at the fixed contactResettable automatic interrupter
LampCircle with radiating lines, or circle with color letter in ladder diagramsCircle with an X insideLight source or indicator
Relay coilCircle with device label (CR, M)Rectangle with designation (-K1)Electromagnet operating contacts
NO contact (control)Two short parallel vertical linesAngled switch blade, openCloses when operated
NC contact (control)Two parallel lines crossed by a diagonalBlade resting on fixed contact with a short perpendicular stopOpens when operated
InductorSeries of loops or humpsSeries of half-circles, or a filled rectangle in older editionsCoil, choke
Transformer (schematic)Two coils facing each other with core lines betweenTwo coils, or two overlapping circles in single-line formMagnetic coupling

Detailed versions of these symbols are in our companion guides on resistor, capacitor, battery and ground symbols and circuit breaker and fuse symbols.

Power Supply, AC/DC and Phase Symbols

Power source symbols are where searchers most often get confused, because the same idea is shown differently on a schematic, a nameplate and a one-line diagram.

SymbolHow it is drawnWhere used
DC voltage source / battery cellA long thin line (positive) parallel to a short thick line (negative); several pairs for a multi-cell batterySchematics, IEEE and IEC
Ideal DC sourceCircle with + and − marks, or with a long/short line pair insideCircuit analysis drawings
AC power sourceCircle containing one cycle of a sine wave (tilde)Schematics, one-lines
Symbol of DC currentSolid horizontal line above a dashed line (⎓), IEC 60417-5031Nameplates, chargers, adapters
Symbol of AC currentTilde ~, IEC 60417-5032Nameplates, meters
AC and DCSolid line over dashed line with a tilde, or ⎓ next to ~Universal input devices
AC to DC converter / rectifierSquare divided by a diagonal, ~ in one half and a straight line (=) in the otherIEC block and one-line diagrams
Single phase symbol1~ or 1Ø, often with frequency, e.g. 1~ 50 HzNameplates, schedules
Three-phase symbol3~ or 3Ø; 3N~ for three-phase with neutralNameplates, motor and transformer data

A power supply on a block diagram is usually drawn as a rectangle labeled with input and output, for example 230 V ~ / 24 V ⎓, while the symbol for a DC power source in a control schematic is often just labeled supply rails marked +24 V and 0 V. Symbols of voltage values follow the same logic: the number plus the AC or DC sign. For three-phase conventions, see our motor control and three-phase symbols guide.

Wire, Connection and Switch Symbols in Wiring Diagrams

Wiring diagram symbols and schematic wiring symbols begin with the conductor itself. The circuit symbol for wire is a straight line. What matters is how lines meet.

  • Connection: a solid dot where lines meet means they are joined. IEC drawings favor T-junctions, offsetting the branches so a four-way crossing never needs to carry a dot.
  • Crossing without connection: two lines crossing with no dot. Older US drawings drew a small semicircular hop on one wire.
  • Terminal: a small open circle; a terminal block is a row of numbered circles or squares.
  • Shielded cable: conductor inside a dashed oval or tube outline, with the shield ground shown.
  • Plug and socket connector: IEC shows a socket as an open semicircle and a pin as a filled bar; IEEE uses arrowheads (male) and V-shapes (female).

Basic electrical switch symbols

The electronic symbol for a switch is a line hinged at one end, angled away from a fixed contact point. A single pole switch symbol (SPST) has one blade and two terminals. A single-pole double-throw (SPDT) has one blade between two fixed contacts. On architectural plans, by contrast, a light switch symbol on an electrical plan is the letter S, with subscripts such as S3 for three-way. The schematic and plan conventions are completely different, which is why the drawing type matters. Switch, pushbutton, limit and relay contacts are covered in depth in the switch and relay symbols guide.

One Line Diagram Symbols for Power Systems

One line diagram symbols (also called single line diagram symbols) represent three-phase power systems with one line per circuit. They are the symbol for power engineering drawings of substations, switchgear and distribution systems.

DeviceTypical single-line symbolNotes
Two-winding transformerTwo overlapping circles (IEC) or two facing coils (IEEE)Winding connections shown as small delta or wye marks
Circuit breakerSmall square box (common US practice) or IEC switch with cross; drawout breakers shown with chevrons at both endsANSI device number 52 in North America
Disconnect switch / isolatorHinged blade; IEC adds a short bar across the fixed contactNo load-break capability unless marked
FuseRectangle with line throughRating noted alongside
Current transformerSmall circle or loop on the line, or a coil beside itRatio noted, e.g. 600/5
Voltage transformerTwo small circles or coils connected from bus to groundRatio noted, e.g. 11,000/110 V
Surge arresterArrow or zigzag in a rectangle to groundConnected line to earth
Generator / motorCircle with G or MRating in kVA or kW beside it
BusbarThick horizontal lineLabeled with voltage and current rating

Our single line diagram guide shows how these symbols combine into a complete drawing, and the transformer symbol guide explains winding and vector group notation.

Electrical Plan Symbols and the Drawing Legend

Electrical symbols for an electrical plan are placed on an architectural floor plan to show where devices are installed, not how they are wired internally. Electrical drawing symbols on plans therefore look simpler: circles for luminaires and receptacles, the letter S for switches, a triangle for a telephone or data outlet, and a rectangle for a panelboard.

Plan symbols fall into families:

  • Electrical lighting symbols: ceiling and wall luminaires, recessed downlights, linear fixtures and exit signs.
  • Receptacle symbols: duplex, single, GFCI, dedicated, floor and special-purpose outlets.
  • Switches and controls: single-pole, three-way, four-way, dimmer and occupancy sensor.
  • Distribution: panelboards, disconnects, transformers, junction boxes and home-run arrows.

Because these symbols are less tightly standardized than schematic symbols, every plan set should carry an electrical legend sheet that defines each symbol and abbreviation used. Residential electrical symbols PDF downloads and similar sheets are useful references, but the project legend governs. Detailed plan conventions are covered in our guides to outlet and receptacle symbols and lighting and plan symbols.

Plans also use text tags: a circuit number next to a device, a home-run arrow labeled with the panel and circuit, and letters such as WP (weatherproof) or GFCI. These tags are as important as the symbols themselves.

Electrical Symbols for CAD and PDF Libraries

Most electrical drawings are produced with CAD block or symbol libraries, so a firm's library effectively becomes its symbol standard. Electrical symbols for CAD, electrical DWG symbols and lighting symbols in CAD should be managed as a controlled library rather than copied ad hoc from old projects.

  1. Pick a base standard per market: IEEE 315 for North American projects, IEC 60617 for IEC projects. Do not mix within one drawing set.
  2. Build blocks with attributes for device tag, rating and circuit number, so schedules can be extracted automatically.
  3. Fix symbol size and insertion point relative to the plotted scale, so text and symbols stay legible.
  4. Create a legend sheet listing every symbol, its standard and its meaning; export it as a PDF for site teams.
  5. Review revisions through a drafting standard so new symbols are added consistently.

A downloadable electrical symbols PDF is useful as a site reference, but check which standard it follows before relying on it. When you receive drawings from an equipment supplier, ask for the legend and the standard used, and confirm that device designations on the drawings match the nameplates on the equipment.

Next Steps: Specifying and Sourcing Switchgear From Drawings

Symbols matter most at procurement. A switchgear or substation RFQ is usually built around a single-line diagram, and every symbol on it becomes a line item. Before issuing the drawing to suppliers:

  • State the symbol standard (IEEE 315 or IEC 60617) and include the legend sheet.
  • Annotate every breaker with frame and trip rating, breaking capacity and type, and every transformer with kVA, voltages, vector group and impedance.
  • Mark CT and VT ratios and accuracy classes, and protection device functions.
  • Identify which devices are drawout, fixed or plug-in, and which are future or spare.
  • Request supplier drawings in the same convention, with a cross-reference to your tags.

MARS builds KYN28 metal-clad switchgear, SF6 ring main units and IEC 61439 LV boards (GGD, GCS, MNS), with drawings provided to IEC or ANSI conventions on request. See the HV and LV switchgear range, and send your single-line diagram via the quote request form.

Frequently asked questions

What are the basic electrical symbols?

The basic electrical symbols include the wire (straight line), connection dot, ground (three horizontal lines of decreasing length), battery (long and short parallel lines), AC source (circle with sine wave), switch (hinged angled line), fuse (rectangle with a line through it), resistor (zigzag or rectangle), lamp (circle with X or radiating lines), motor (circle with M) and transformer (two coils or two circles).

What is the difference between IEEE and IEC electrical symbols?

IEEE 315 symbols are used mainly in North America, while IEC 60617 symbols are used in Europe and most other regions. The largest differences are in resistors (zigzag vs rectangle), lamps, control contacts, relay coils (circle vs rectangle) and breakers. Wires, ground and battery symbols are nearly the same in both standards.

What is the symbol for DC current?

The symbol for direct current is a solid horizontal line with a dashed line beneath it, defined in IEC 60417-5031. It appears on adapters, chargers and equipment nameplates. On schematics, a DC source is drawn as a battery symbol, with the longer line marking the positive terminal, or as supply rails labeled with plus and minus voltages.

What does a dot mean on a wiring diagram?

A solid dot where two or more lines meet indicates an electrical connection between those conductors. Lines that cross without a dot are not connected. To avoid confusion, IEC drafting practice recommends T-junctions instead of four-way junctions, and some older North American drawings show non-connected crossings with a small semicircular hop.

Where can I find a complete electrical symbols chart?

The authoritative sources are the IEEE 315 standard for North American practice and the IEC 60617 online database for IEC practice. For a specific project, the governing chart is the legend sheet in the drawing set, which lists every symbol and abbreviation the designer used, including any non-standard or company-specific symbols.

What is the single line diagram symbol for a circuit breaker?

On North American single line diagrams a circuit breaker is commonly drawn as a small square, often labeled 52 per IEEE C37.2 device numbering, with chevrons on both sides when it is drawout. IEC single line diagrams draw a switch contact with a small cross at the fixed contact. Ratings are written beside the symbol.

Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .

Tags: electrical symbols electrical symbols chart circuit diagram symbols wiring diagram symbols single line diagram symbols

More guides