Switchgear & Substations

Single Line Diagram Guide: Symbols, Reading & Examples

Printed single line diagram on an engineer's desk in a substation control room with switchgear behind

Key takeaways

  • A single line diagram represents a three-phase circuit with one line, so a 13.8 kV feeder and its three conductors appear as a single path.
  • Symbols follow IEEE 315 / ANSI Y32.2 in North America and IEC 60617 elsewhere; protection functions use ANSI C37.2 device numbers such as 52, 50/51 and 87.
  • Every transformer on an SLD should show kVA, primary and secondary voltage, vector group or connection, and percent impedance for fault studies.
  • A 1,500 kVA transformer at 480 V with 5.75% impedance can deliver about 31 kA of symmetrical fault current, which the SLD must make visible.
  • The SLD is the master document for short-circuit, arc flash (IEEE 1584) and coordination studies, so it must be updated whenever equipment changes.

Quick answer: A single line diagram (one line diagram, SLD or unifilar diagram) is a simplified drawing of a power system that shows all three phases as one line. It traces the path of power from source to load through transformers, switchgear, breakers, fuses and buses, and lists ratings such as kVA, voltage, impedance, interrupting capacity and protection functions.

The single line diagram is the first drawing an engineer asks for when a project starts and the last one updated when it closes. Utilities require it for interconnection, insurers and authorities use it for arc flash labelling, and switchgear and transformer manufacturers quote directly from it. If the SLD is wrong, every study and purchase order built on it inherits the error.

This guide is written for electrical engineers, contractors, facility managers and buyers who need to read, check or prepare an electrical single line diagram. It covers what the drawing shows, the symbols that matter, a step-by-step reading method, worked fault-level numbers and real layouts for substations, switchyards and data centers.

What Is a Single Line Diagram? Meaning and Purpose

A single line diagram is a schematic representation of a power system in which each balanced three-phase circuit is drawn as one line, and each piece of equipment is shown by a standard symbol with its key rating. The terms one line diagram, electrical one line, SLD electrical drawing and unifilar diagram (common in Spanish- and Portuguese-speaking markets) all mean the same thing.

The single line diagram meaning is best understood by what it leaves out. It does not show individual control wires, terminal numbers or the physical position of equipment. Those belong on schematic and wiring drawings, covered in our electrical wiring diagram guide. Instead, the SLD answers system-level questions:

  • Where does power come from (utility, generator, battery storage, PV), and at what voltage and fault level?
  • How many transformations occur, and what are the kVA ratings and impedances?
  • Which breakers, fuses and disconnects can isolate each part of the system?
  • Which buses are normally open or closed, and where are ties and transfer switches?
  • Where are current and voltage transformers, meters and protective relays located?

The electrical single line diagram is the basis for load flow, short-circuit, coordination and arc flash studies, and operators plan isolation from it. A single line diagram of a power system therefore spans generation, transmission, substations and distribution, while a building SLD may start at the utility meter and stop at the final panelboards.

Electrical One Line Diagram Symbols You Must Know

Symbols on a one line electrical drawing follow IEEE 315 (ANSI Y32.2) in North America and IEC 60617 in most other markets. Projects often mix both, so the legend sheet matters. For a wider symbol reference see our electrical symbols guide and the dedicated page on circuit breaker and fuse symbols.

DeviceANSI / IEEE 315 styleIEC 60617 styleRatings shown beside it
Two-winding transformerTwo interlocking coils or circlesTwo overlapping circleskVA, kV ratio, %Z, connection (e.g., Dyn11)
Circuit breaker (MV)Square box, often labelled 52Switch with a cross (x) on the contactRated current, interrupting kA, drawout or fixed
LV breaker / MCBCurved arc contact or boxSwitch with x; curve and poles notedFrame/trip amps, poles, curve (B, C, D), kA
FuseRectangle on the line or S-curveRectangle with line through itAmpere rating, class or type (E-rated, gG, aM)
Disconnect / disconnectorOpen blade at an angleBlade with a short bar on the fixed contactAmps, kV, load-break or not
Current transformerSmall circle or loop on the lineCircle threaded by the conductorRatio, e.g., 600:5, accuracy class
BusHeavy horizontal lineHeavy lineAmps, kV, short-time kA

The electrical disconnect symbol deserves care. In IEC drawings a disconnector (isolator) has a short perpendicular bar at the fixed contact, a switch-disconnector adds the load-break semicircle, and a fuse-switch combination places the fuse rectangle in the blade. In ANSI drawings the blade symbol is labelled 89 for line disconnects. The MCB symbol in a single line diagram is usually the IEC breaker symbol with text such as C32 3P 10 kA; residual-current devices add a toroid or the label RCD/RCBO. Protective relays are drawn as circles carrying ANSI C37.2 numbers: 27 undervoltage, 50/51 overcurrent, 50N/51N ground overcurrent, 59 overvoltage, 86 lockout and 87T transformer differential.

How to Read a Single Line Diagram Step by Step

Learning how to read a one line diagram is mostly about discipline: follow the energy, then check the numbers. The method below works for a small commercial building or a 110 kV substation. If you are new to drawing sets in general, our guide on how to read electrical drawings explains title blocks, revisions and sheet numbering.

  1. Read the legend and notes. Confirm the symbol standard, abbreviations, normally open (NO) and normally closed (NC) conventions and the revision status.
  2. Locate every source. Identify utility services, generators, UPS outputs and battery energy storage, with available fault current or X/R ratio at each point of connection.
  3. Trace power downward. Follow each line from the source through the incoming switchgear, transformers and buses to the outgoing feeders, noting voltage at each level.
  4. Check transformer data. Record kVA, voltages, %Z, vector group and grounding method (solid, resistance, ungrounded) for each unit.
  5. Identify isolation points. Mark the breakers, fuses and disconnects that would isolate each bus; confirm ties and interlocks such as main-tie-main schemes.
  6. Review protection and metering. Match CT ratios and relay device numbers to the equipment they protect; confirm that each transformer has primary and secondary protection.
  7. Verify ratings against fault level. Compare breaker interrupting ratings and bus short-time ratings with calculated fault current at each bus.

Treat any device drawn without a rating as an open question, and confirm the normal switching state shown matches how the site actually operates.

Single Line Diagram Example: Ratings and a Fault-Level Check

A simple single line diagram example for an industrial plant might read: utility 13.8 kV, 250 MVA available fault level; a 13.8 kV fused load-break switch; a 1,500 kVA, 13.8 kV to 480Y/277 V, Dyn1, 5.75% impedance transformer; a 2,000 A main breaker; and a 480 V switchboard feeding motor control centers and panelboards. The numbers written on the SLD are what make it useful, so check them.

Full-load current. Use I = S / (√3 × V).

  • Primary: 1,500,000 / (1.732 × 13,800) = 62.8 A
  • Secondary: 1,500,000 / (1.732 × 480) = 1,804 A, so a 2,000 A main breaker and bus are reasonable.

Maximum secondary fault current (infinite-bus approximation). Use Isc = IFL / Z(pu): 1,804 / 0.0575 = 31,400 A, about 31.4 kA symmetrical.

Including the utility source. Convert the source to per-unit on the transformer base: Zs = 1.5 MVA / 250 MVA = 0.006 pu. Total Z = 0.006 + 0.0575 = 0.0635 pu, giving 1,804 / 0.0635 = 28,400 A. Motor contribution would add to this. A 480 V board with 35 kA or higher interrupting rating is therefore the minimum; many specifiers choose 50 kA or 65 kA for margin and future changes. See our fault current calculation guide for X/R ratios and motor contribution.

These values also feed an arc flash study.

Substation One Line Diagram and Switchyard Bus Schemes

A single line diagram of a substation is dominated by the bus arrangement, because the scheme decides how many breakers are needed and what happens when one fails. A switchyard single line diagram at transmission voltage shows line bays, transformer bays, bus couplers, disconnectors (89), earthing switches, CTs, VTs and surge arresters for each bay. For broader context on layouts and drawing types, see our electric substation diagram guide.

Bus schemeBreakers per circuitReliabilityTypical use
Single bus1Bus fault drops all circuitsSmall distribution and compact substations
Sectionalized single bus1 plus bus-section breakerHalf the circuits survive a bus faultIndustrial and utility MV switchboards
Main-tie-main2 mains plus 1 tieEither source can carry the loadHospitals, plants, data centers
Ring bus1Any breaker can be removed without outageHV substations with 4–6 circuits
Breaker-and-a-half1.5High; bus faults do not drop circuitsTransmission switchyards
Double bus, single breaker1 plus couplerCircuits can be moved between busesLarge grid substations

A typical 110/10 kV substation one line diagram shows incoming lines with line disconnectors and earthing switches, HV breakers, one or two power transformers with on-load tap changers and neutral earthing, then 10 kV metal-clad switchgear with a bus-section breaker, outgoing feeders, station service transformer and capacitor bank. Compact substations compress this into one enclosure: RMU, distribution transformer and LV board on one sheet.

Data Center One Line Diagram: Redundancy on Paper

A data center one line diagram is where redundancy concepts become visible. Designers label architectures as N, N+1, 2N or distributed redundant, and the SLD proves whether a single failure (a transformer, a breaker, a UPS module) can interrupt IT load. Our data center power distribution article covers topologies; on the drawing, look for:

  • Utility and MV level: dual utility feeds or one feed with a main-tie-main MV switchboard; MV ring main units for unit substations.
  • Transformation: unit substation transformers, usually cast-resin dry-type indoors or liquid-filled outdoors, each sized so the surviving unit can carry the critical load if its partner fails.
  • Standby generation: generators connected through paralleling switchgear or automatic transfer switches; the SLD must show which loads are on which bus during transfer. See our automatic transfer switch guide.
  • UPS and storage: UPS modules with maintenance bypass, plus any battery energy storage.
  • Distribution: PDUs, busway and static transfer switches to rack level.

A 2N design shows two completely independent paths, A and B, from utility (or generator) to the dual-corded IT equipment. Check that the A and B sides never share a bus, breaker or transformer, and that tie breakers are shown normally open with interlocks noted.

How to Draw an Electrical Single Line Diagram

Whether you produce a single line drawing electrical sheet by hand for a small site or in electrical CAD for a utility substation, the content rules are the same. Software choices are covered in our electrical design software guide; the drawing conventions below apply regardless of tool.

  • Flow top to bottom (or left to right). Put the highest voltage at the top and the loads at the bottom, so power flows in one visual direction.
  • One voltage level per band. Group equipment by voltage and label each bus with its nominal kV, phases, wires and frequency, e.g., 480Y/277 V, 3-phase, 4-wire, 60 Hz.
  • Rate every device. Breakers need trip rating and interrupting kA; transformers need kVA, %Z and connection; cables need size, conductor material and length when used for studies.
  • Show grounding. Indicate solid, resistance or reactance grounding and neutral earthing resistors.
  • Use unique IDs. Tag equipment consistently, for example with IEC 81346 reference designations or a site tag scheme, so the SLD links to schedules and specifications.
  • Mark the normal state. Draw normally open devices clearly and add a note on interlocks and transfer logic.
  • Control revisions. Keep the as-built SLD current; NFPA 70E labels depend on it.

A one-page single line diagram sample for a small facility may show only a transformer, a main switchboard and five feeders; larger sites need a key one-line plus detailed sheets.

Next Steps: Specifying and Sourcing from Your SLD

A complete single line diagram is the fastest way to get an accurate quotation for transformers, switchgear and substations. When MARS receives an SLD with ratings, engineers can confirm transformer kVA and impedance, switchgear interrupting ratings and protection scope in one review instead of several rounds of questions.

Include the following with an RFQ:

  • The SLD (PDF and, if available, the native CAD file) with revision status.
  • Utility voltage, frequency (50 or 60 Hz), available fault level and grounding method.
  • Transformer data: kVA, voltage ratio, taps, vector group, %Z target, cooling, and whether oil-immersed or cast-resin dry-type is required.
  • Switchgear data: MV type (metal-clad withdrawable or SF6 ring main unit), LV board form and standard (IEC 61439 or UL/ANSI), busbar ratings and short-time kA.
  • Applicable standards (IEC 60076, IEC 62271, IEEE C57.12.00, IEEE C37) and any utility specifications.
  • Site conditions: altitude, ambient temperature, indoor or outdoor, and the required IP or NEMA rating.

MARS designs and builds compact, box-type and containerised transformer substations, together with matching HV and LV switchgear, to IEC 60076 and IEC 62271 with ANSI/IEEE, GB and GOST variants. Every unit receives routine tests and you are welcome to attend FAT; typical lead time is 25–45 days for distribution transformers and switchgear. Send your single line diagram through the request a quote page and the engineering team will return a technical and commercial offer.

Frequently asked questions

What is the difference between a single line diagram and a wiring diagram?

A single line diagram shows the power system at a high level, drawing three phases as one line with ratings for transformers, breakers and buses. A wiring diagram shows every conductor, terminal and wire number for a specific panel or machine. The SLD is used for studies, switching and procurement, while wiring diagrams are used for building and troubleshooting equipment.

Why is it called a one line diagram?

It is called a one line diagram because a balanced three-phase circuit is represented by a single line instead of three or four separate conductors. This simplification is valid for system studies under balanced conditions and makes complex networks readable. Where single-phase or unbalanced details matter, notes such as 3-phase, 4-wire or 1-phase, 3-wire are added beside the line.

What does SLD mean in electrical engineering?

SLD stands for single line diagram, also called a one line diagram or unifilar diagram. It is the master drawing of an electrical power system, showing sources, transformers, switchgear, protection devices, buses and major loads with their ratings. Engineers use it for short-circuit, coordination and arc flash studies, and operators use it to plan safe switching and isolation.

What information should a substation single line diagram include?

A substation single line diagram should show incoming lines, bus arrangement, circuit breakers, disconnectors and earthing switches, power transformers with kVA, voltage ratio, impedance, vector group and tap changer, neutral grounding, CTs and VTs with ratios, protective relay functions by ANSI device number, surge arresters, station service supply and outgoing feeders with their ratings.

How do you show a transformer on a single line diagram?

A transformer is drawn as two overlapping circles (IEC) or two coil symbols (ANSI) with text giving its kVA or MVA rating, primary and secondary voltages, connection or vector group such as Dyn11, percent impedance, cooling class and tap range. The grounding of the neutral, whether solid or through a resistor, is shown at the winding symbol.

Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .

Tags: single line diagram one line diagram electrical single line diagram substation one line diagram how to read a single line diagram

More guides