
Key takeaways
- Low voltage is 1,000 V AC or 1,500 V DC and below under IEC and the EU Low Voltage Directive, which covers 50–1,000 V AC.
- ANSI C84.1 defines medium voltage as above 1,000 V and below 100 kV, and high voltage as 100 kV up to 230 kV.
- Extra high voltage normally means transmission above 230 kV, such as 345, 400, 500 and 765 kV, while UHV starts around 1,000 kV AC.
- Equipment is rated by its highest voltage Um, such as 12 kV for 10–11 kV systems, with a lightning impulse level such as 75 kV.
- Raising voltage from 11 kV to 33 kV cuts current to one third for the same power and resistive losses to about one ninth.
Quick answer: High voltage means different things in different standards. In IEC usage, anything above 1,000 V AC is high voltage in the broad sense, and power engineers split it into medium voltage (about 1–35 kV), high voltage (about 35–230 kV) and extra high voltage (above 230 kV). ANSI C84.1 places medium voltage above 1 kV and below 100 kV, and high voltage from 100 kV to 230 kV.
Ask five engineers what is considered high voltage and you may get five answers: above 600 V, above 1,000 V, above 35 kV or above 100 kV. Each is correct in its own context, because safety codes, product standards and utility planning documents draw the lines differently. The confusion matters when you write a specification, select switchgear or decide who is qualified to work on a system.
This guide is for engineers, buyers and technicians who need a clear map of voltage levels. It compares the low, medium, high and extra high voltage ranges under IEC and ANSI, explains the kilovolt unit and its abbreviation, lists common system voltages with their equipment ratings, works through why higher voltage reduces losses, and shows how voltage class changes equipment and safety requirements.
What Is Considered High Voltage?
High voltage, in the broadest engineering sense, is any voltage high enough that the equipment and installation rules for low voltage no longer apply, which internationally means above 1,000 V AC or 1,500 V DC. That is how IEC 61936-1 (power installations exceeding 1 kV AC) and the IEC 62271 switchgear series use the term. Under this definition, an 11 kV ring main unit and a 400 kV transmission line are both high voltage.
Within the power industry, though, "high voltage" is usually narrower. Utilities and planners reserve it for subtransmission and transmission levels, roughly 35 kV or 69 kV up to 230 kV, and use medium voltage for distribution between 1 kV and about 35 kV. So what voltage is high voltage depends on who is speaking:
- Safety and installation codes: often a single threshold at 1,000 V; older North American documents used 600 V.
- Product standards: IEC 62271 covers switchgear above 1 kV, while IEC 60947 and IEC 61439 cover LV equipment.
- Utility planning and ANSI C84.1: separate LV, MV, HV and extra high voltage classes.
To define high voltage correctly in a specification, state the standard you are using, or simply state the nominal system voltage and the equipment's highest voltage rating. That avoids any ambiguity.
Low, Medium and High Voltage Ranges Compared
The table below summarizes the most common high voltage, medium voltage and low voltage ranges used in practice. Boundaries vary by country and utility, so treat them as conventions rather than absolute limits.
| Class | IEC / international practice | ANSI C84.1 / North American practice | Typical uses |
|---|---|---|---|
| Extra-low voltage (ELV) | ≤ 50 V AC, ≤ 120 V ripple-free DC | NEC Class 2 circuits use similar or lower limits | Controls, telecom, lighting |
| Low voltage (LV) | 50–1,000 V AC; 75–1,500 V DC | ≤ 1,000 V | Buildings, motors, LV switchboards, 400/230 V, 480/277 V |
| Medium voltage (MV) | Above 1 kV to about 35 kV (Um up to 36 or 40.5 kV) | Above 1 kV to below 100 kV | Distribution feeders, industrial plants, RMUs |
| High voltage (HV) | About 35–230 kV | 100–230 kV | Subtransmission, large substations |
| Extra high voltage (EHV) | Above 230 kV (Um 245–800 kV) | Above 230 kV to 1,000 kV | Bulk transmission |
| Ultra high voltage (UHV) | 1,000 kV AC and above; ±800 kV DC and above | Above 1,000 kV | Long-distance bulk transmission |
IEC 60038, the standard voltages document, groups its tables in a similar way: systems from 1 kV to 35 kV, from 35 kV to 230 kV, and above 245 kV by highest voltage for equipment. Hence 35 kV is the usual IEC medium voltage ceiling. For how these voltages appear across the grid, see our article on power distribution voltages.
What Is Considered Medium Voltage?
Medium voltage is the distribution voltage class between low-voltage utilization and high-voltage transmission, typically above 1 kV and up to about 35 kV in IEC markets, or up to 69 kV in North American utility practice. The medium voltage meaning in a specification is usually a system such as 6.6 kV, 10 kV, 11 kV, 13.8 kV, 20 kV, 22 kV, 33 kV or 34.5 kV.
When someone writes "voltage MV" or "MV level" on a drawing, they mean this distribution class, not megavolts. Common MV level applications include:
- Utility primary distribution feeders and ring circuits.
- Industrial plant distribution and large motors at 3.3, 4.16, 6.6 or 11 kV.
- Wind and solar collector systems, commonly 33–34.5 kV.
- Data center and hospital campus distribution.
Low voltage vs medium voltage
Crossing 1 kV changes almost everything. Insulation must handle partial discharge and impulse stress, so equipment is dielectric-tested at power frequency and with lightning impulses. Switching moves from air or molded-case breakers to vacuum or SF6 breakers, and enclosure design follows IEC 62271-200 with internal arc classification. Cables need semiconducting screens and stress-control terminations. Workers need medium-voltage qualifications, and installations follow IEC 61936-1 or the NEC requirements for over 1,000 V. Our medium voltage electrical systems guide and low voltage electrical systems guide cover each class in detail.
High Voltage vs Medium Voltage, and What Is Extra High Voltage?
The step from medium to high voltage is driven by distance and power. Medium voltage carries tens of megawatts over tens of kilometers; high voltage carries hundreds of megawatts over hundreds of kilometers.
Key differences between high voltage vs medium voltage equipment:
- Insulation coordination: at HV, switching surges become important alongside lightning, and surge arrester selection is a formal study.
- Switchgear: air-insulated outdoor substations or gas-insulated switchgear, with SF6 or alternative-gas breakers, replace indoor metal-clad panels.
- Grounding: HV systems are normally solidly grounded at transformer neutrals; MV systems may be solidly, resistance or resonant grounded.
- Transformers: on-load tap changers, large oil volumes and dedicated protection such as differential and Buchholz relays.
Extra high voltage (EHV) is transmission at system voltages above 230 kV, typically 345 kV, 400 kV, 500 kV and 765 kV AC. The extra high voltage range exists because transmitting gigawatts over long distances at lower voltages would need impractically high currents. At EHV, corona loss, audible noise and conductor bundling become design drivers, and switching overvoltages often govern insulation more than lightning. Above roughly 1,000 kV AC, or ±800 kV DC, the industry uses the term ultra high voltage. For substation layouts at these levels, see our guide on what a substation is.
What Is a Kilovolt? Units and Abbreviations
A kilovolt is a unit of electrical potential equal to 1,000 volts. The kilovolt abbreviation is kV, with a lowercase k (the SI prefix kilo) and a capital V (volt, named after Volta). Writing "KV" or "Kv" is common but technically incorrect.
| Unit | Symbol | Value in volts | Example |
|---|---|---|---|
| Volt | V | 1 | 230 V socket outlet |
| Kilovolt | kV | 1,000 | 11 kV distribution feeder |
| Megavolt | MV | 1,000,000 | Lightning, particle accelerators |
Note the clash: in physics MV means megavolt, but in power engineering MV almost always means medium voltage. Spell it out at first use.
Conversions and related units
- Volts to kilovolts: divide by 1,000; 13,800 V = 13.8 kV.
- kVA (kilovolt-ampere) is apparent power, not voltage:
S = √3 × V × Ifor three-phase. - kVp or kV peak is the crest value, used for impulse levels; kV rms is the effective value used for system voltages. For a sine wave,
V_peak = √2 × V_rms, so 11 kV line-to-line corresponds to a line-to-ground peak of11 × √2 / √3 = 8.98 kV.
For more on symbols, see our electrical abbreviations list.
Standard System Voltages and Equipment Voltage Ratings
A voltage level on a single-line diagram is the nominal system voltage. Equipment is rated by its highest voltage for equipment (Um or rated voltage Ur), which must be at least the maximum operating voltage of the system, plus insulation levels proven by test.
| Nominal system voltage | Equipment rated voltage | Power-frequency withstand (1 min) | Lightning impulse withstand (BIL) |
|---|---|---|---|
| 400/230 V, 480/277 V | 690 V or 1,000 V | Per IEC 61439 / UL | Per overvoltage category |
| 6.6 kV | 7.2 kV | 20 kV | 60 kV |
| 10–11 kV | 12 kV | 28 kV | 75 kV |
| 13.8 kV (IEEE) | 15 kV | 36 kV | 95 kV |
| 20–22 kV | 24 kV | 50 kV | 125 kV |
| 33–35 kV | 36 kV or 40.5 kV | 70 kV or 95 kV | 170 kV or 185 kV |
| 110–132 kV | 126 kV or 145 kV | 230–275 kV | 550–650 kV |
MV values follow IEC 62271-1 and IEC 60071-1 (List 2 impulse levels shown for 7.2–24 kV) and IEEE C37.20.2 for 15 kV. Higher-voltage withstand values depend on the insulation coordination study and the standard series chosen. Always read both the voltage rating and the insulation levels on a data sheet; two 36 kV switchboards can have different BIL. For a typical North American MV example, see our 15 kV switchgear engineering guide.
Why Use Higher Voltage? A Worked Example
Power systems step voltage up for transmission because, for the same power, current falls in proportion to voltage and resistive losses fall with the square of current.
Example. A 10 MW load at 0.9 power factor must be supplied over a 10 km overhead line. Three-phase current is I = P / (√3 × V × PF).
- At 400 V:
I = 10,000,000 / (1.732 × 400 × 0.9) = 16,038 A, clearly impractical. - At 11 kV:
I = 10,000,000 / (1.732 × 11,000 × 0.9) = 583 A. - At 33 kV:
I = 10,000,000 / (1.732 × 33,000 × 0.9) = 194 A.
Line loss is P_loss = 3 × I² × R. If the conductor has 0.2 Ω/km, R = 2 Ω per phase:
- At 11 kV:
3 × 583² × 2 = 2.04 MW, about 20% of the load, which also means severe voltage drop. - At 33 kV:
3 × 194² × 2 = 0.226 MW, about 2.3%.
Tripling the voltage reduces losses by a factor of nine. In practice, 11 kV would be used with a much larger conductor or a shorter route, while 33 kV is the natural voltage level for this transfer. The same logic explains 110 kV and EHV transmission for hundreds of megawatts. The cost is more insulation, larger clearances and more expensive switchgear, so each voltage step is a balance. For transformer design at these levels, see our high voltage transformer engineering guide.
How Voltage Level Changes Safety and Testing Requirements
Voltage class sets the rules for who can work on equipment, how close they can approach and how equipment is tested.
- Approach boundaries: NFPA 70E tables set limited and restricted approach boundaries that grow with voltage. EN 50110 and national rules define live working zones similarly.
- Qualification: MV and HV switching usually requires specific authorization, switching programs and earthing procedures.
- Earthing before work: above 1 kV, de-energized conductors must be verified dead and earthed with rated portable earthing equipment, because induced and capacitive voltages remain.
- Clearances: IEC 61936-1 sets minimum phase-to-earth and phase-to-phase clearances and safety distances by Um.
- Testing: MV and HV insulation is tested with power-frequency, impulse and partial discharge tests; see our partial discharge testing guide. Field cable tests use very-low-frequency or DC methods.
- Overvoltage protection: arresters are selected by system voltage and grounding; see our surge arrester guide.
Test voltages for acceptance and maintenance testing also scale with the voltage class, so a single test plan rarely covers both LV and MV equipment. When writing procedures, always reference the specific nominal voltage rather than a generic class name, so there is no doubt which rules apply.
Next Steps: Specifying and Sourcing Equipment by Voltage Level
MARS manufactures equipment across the LV, MV and HV classes: IEC 61439 low-voltage switchboards, KYN28 metal-clad switchgear and SF6 ring main units for MV distribution, distribution and pad- or pole-mounted transformers, and power transformers up to 31,500 kVA in the 110 kV class.
To avoid voltage ambiguity in an RFQ, state:
- Nominal system voltage and frequency (for example 11 kV, 50 Hz or 13.8 kV, 60 Hz).
- Highest voltage for equipment (Um) and required insulation levels: power-frequency withstand and BIL.
- System grounding method: solid, resistance, resonant or isolated.
- Altitude, since insulation must be corrected above 1,000 m.
- Standard set: IEC, ANSI/IEEE, GB or GOST.
If a project spans several voltage classes, for example a 110 kV/33 kV/0.4 kV scheme, list each level separately with its equipment rating and insulation level; a single "HV" label invites errors in drawings and procurement. Routine tests on every MARS unit are performed at the insulation levels you specify, and FAT can be witnessed.
Explore our HV and LV switchgear and power transformers, then request a quote with your single-line diagram.
Frequently asked questions
What voltage is considered high voltage?
Internationally, any voltage above 1,000 V AC or 1,500 V DC is high voltage for installation and equipment purposes. In utility practice the term is narrower: medium voltage covers about 1–35 kV, high voltage about 35–230 kV, and extra high voltage above 230 kV. Always check which standard a document uses.
What is the medium voltage range?
Medium voltage is generally above 1 kV and up to about 35 kV in IEC markets, with common levels of 6.6, 11, 20 and 33 kV. ANSI C84.1 defines medium voltage more broadly as above 1,000 V and below 100 kV, which includes 69 kV subtransmission in North America.
What is extra high voltage?
Extra high voltage refers to AC transmission above 230 kV, typically 345, 400, 500 and 765 kV. It is used to move very large blocks of power over long distances with acceptable losses. Above about 1,000 kV AC or ±800 kV DC, the term ultra high voltage is used.
What is the abbreviation for kilovolt?
The abbreviation is kV, with a lowercase k for the SI prefix kilo and a capital V for volt. One kilovolt equals 1,000 volts, so 13,800 V is 13.8 kV. Do not confuse kV with kVA, a unit of power.
Is 480 V high voltage?
No. Under IEC, ANSI C84.1 and the NEC, 480 V is low voltage because it is below 1,000 V. It is still dangerous: 480 V systems can deliver high fault currents and severe arc flash energy, so NFPA 70E requirements apply.
What is the difference between low voltage and medium voltage equipment?
Medium voltage equipment must withstand impulse and partial discharge stresses, so it is tested with lightning impulse and power-frequency voltages, uses vacuum or SF6 breakers, screened cables and IEC 62271 switchgear. Low voltage equipment follows IEC 60947 and IEC 61439, with air and molded-case breakers.
Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .
Tags: what is high voltage what is considered high voltage medium voltage range what is extra high voltage low medium high voltage ranges


