
Key takeaways
- Breaker labels such as 400AF/320AT 65 kAIC give frame size, trip rating and interrupting rating, which must exceed the available fault current at that bus.
- Panel abbreviations identify purpose: PP is a power panel, LP a lighting panel, RP a receptacle panel, DP a distribution panel and MDP the main distribution panel.
- IEC breaker data uses Icu, Ics and Icw for short-circuit ratings, while North American labels use AIC or kAIC and SCCR for assemblies.
- HVAC nameplates give MCA for conductor sizing and MOCP for the largest permitted overcurrent device, per the equipment listing.
- Drawing notes such as AFF, TYP, NIC, ETR and EC change scope and dimensions, so they must be read with the same care as symbols.
Quick answer: Electrical abbreviations are short codes used on drawings, panel schedules, breaker labels and nameplates. Common examples: CB (circuit breaker), MCCB (molded case circuit breaker), AIC (amperes interrupting capacity), PP (power panel), LP (lighting panel), MDP (main distribution panel), ATS (automatic transfer switch), AFF (above finished floor) and NIC (not in contract). Always confirm meanings against the project legend.
Electrical documents compress a great deal of meaning into two to five letters. A note reading “ETR, RL 600 mm AFF, EC to extend HR to PP-2” is perfectly clear to an experienced electrician and impenetrable to almost everyone else. Misreading one abbreviation can change a scope of work, a breaker rating or a mounting height.
This electrical abbreviations list is for engineers, electricians, estimators, facility managers and buyers who work with drawings, panel schedules, breaker box labels and equipment nameplates. It groups abbreviations by where you meet them, gives IEC equivalents where North American and international practice differ, and decodes a few real-world labels. Work on panels and service equipment must follow local code and be done by a licensed electrician.
Abbreviation for Breaker: Circuit Breaker Abbreviations
Circuit breaker abbreviations describe the device type, its ratings and its accessories. The basic abbreviation for breaker is CB; on IEC drawings breakers are tagged -Q followed by a number.
| Abbreviation | Meaning | Notes |
|---|---|---|
| CB / BKR | Circuit breaker | Generic |
| MCB | Miniature circuit breaker | DIN-rail, IEC 60898-1 or IEC 60947-2 |
| MCCB | Molded case circuit breaker | UL 489 or IEC 60947-2 |
| ACB | Air circuit breaker | LV power breaker, often drawout |
| ICCB / LVPCB | Insulated case / low-voltage power circuit breaker | North American LV power breakers |
| VCB | Vacuum circuit breaker | MV switchgear |
| GFCI | Ground-fault circuit interrupter | Personnel protection, about 5 mA trip in North America |
| AFCI | Arc-fault circuit interrupter | Dwelling branch circuits per NEC 210.12 |
| GFPE | Ground-fault protection of equipment | Required on certain large services per NEC 230.95 |
| RCD / RCCB / RCBO | Residual current device / without / with overcurrent protection | IEC equivalents of GFCI-type protection |
| AF / AT | Ampere frame / ampere trip | e.g. 250AF/200AT |
| AIC / kAIC | Amperes interrupting capacity | Maximum fault current the breaker can interrupt |
| LSIG | Long-time, short-time, instantaneous, ground | Electronic trip unit functions |
| ST or SHT | Shunt trip | Remote tripping coil |
| UVR | Undervoltage release | Trips on loss of voltage |
| AUX / AL | Auxiliary contact / alarm (bell) contact | Status indication |
| MO | Motor operator | Remote open and close |
For the physical device types behind these codes, see the circuit breaker types guide; for the matching drawing symbols, see the circuit breaker and fuse symbols guide.
Breaker Box Abbreviations on Panel Directories
Breaker box abbreviations are the short labels written on panel directories and panel schedules to identify each circuit's load. They are not standardized, but these are widespread in North American practice:
| Label | Load | Label | Load |
|---|---|---|---|
| LTG / LTS | Lighting | REC / RECEPT | Receptacles |
| KIT | Kitchen | BATH | Bathroom |
| DW | Dishwasher | DISP | Disposal |
| MW | Microwave | REF / FRIG | Refrigerator |
| WH / WTR HTR | Water heater | DRY | Dryer |
| WASH / W | Washer | RNG | Range |
| A/C / AC | Air conditioner | FURN / AHU | Furnace / air handling unit |
| HP | Heat pump | EVSE / EV | Electric vehicle charger |
| SPR / SP | Spare (breaker fitted) | SPC | Space (no breaker) |
| GFCI / GF | GFCI-protected circuit | AFCI / CAFCI | Arc-fault protected circuit |
NEC 408.4(A) requires each circuit to be legibly identified as to its clear, evident and specific purpose, so labels like “misc” or “general” are not acceptable. On commercial panel schedules, a circuit line usually also shows the load in VA, the breaker trip and poles, and the phase, such as 20A/1P, A, 1,440 VA, REC RM 104.
The panel schedule guide shows how these entries roll up into panel and feeder loads, and the electrical panel guide explains panel construction and ratings.
PP Panel Electrical Meaning and Other Equipment Abbreviations
On one-line diagrams and riser drawings, equipment is named with abbreviations that indicate its function. The PP panel electrical meaning is power panel: a panelboard serving power loads such as motors, HVAC equipment and receptacles, often at 480 V or 208 V three-phase.
| Abbreviation | Equipment |
|---|---|
| MSB / MDP / MDB | Main switchboard / main distribution panel / main distribution board |
| SWBD | Switchboard |
| SWGR | Switchgear |
| PP / PNL | Power panel / panel |
| LP | Lighting panel |
| RP | Receptacle panel |
| DP | Distribution panel |
| ELP / EPP | Emergency lighting panel / emergency power panel |
| MCC | Motor control center |
| ATS / MTS | Automatic / manual transfer switch |
| UPS | Uninterruptible power supply |
| VFD / VSD | Variable frequency / speed drive |
| XFMR / TX / TR | Transformer |
| RMU | Ring main unit |
| AIS / GIS | Air-insulated / gas-insulated switchgear or substation |
| CT / VT (PT) | Current transformer / voltage (potential) transformer |
| BESS / PCS | Battery energy storage system / power conversion system |
| GEN | Generator |
| DISC / DS | Disconnect switch |
A panel name usually combines the type with a number and sometimes voltage or floor, for example PP-2A or LP-3H (H for 480Y/277 V, L for 208Y/120 V in many firms' conventions). The switchboard vs panelboard guide explains where the boundaries between these equipment classes lie. Transformer-specific abbreviations such as ONAN, BIL and HV/LV are listed in the transformer abbreviation guide.
Electrical Drawing and Specification Abbreviations
Drawing notes use abbreviations that affect scope, dimensions and materials. These are among the most frequently misread electrical acronyms.
| Abbreviation | Meaning |
|---|---|
| AFF / AFG | Above finished floor / above finished grade |
| TYP | Typical: applies to all similar locations |
| NIC | Not in contract |
| EC / GC / MC | Electrical / general / mechanical contractor |
| ETR / RL / RM | Existing to remain / relocate / remove |
| (E) / (N) / (F) | Existing / new / future |
| HR | Home run to panel |
| JB / J-BOX | Junction box |
| WP / WR | Weatherproof / weather-resistant |
| EM | Emergency |
| IG | Isolated ground |
| EMT / IMC / RMC (GRC) | Electrical metallic tubing / intermediate metal conduit / rigid metal (galvanized rigid) conduit |
| PVC / ENT / LFMC | Rigid PVC conduit / electrical nonmetallic tubing / liquidtight flexible metal conduit |
| MC / AC | Metal-clad cable / armored cable (context distinguishes from mechanical contractor) |
| THHN / THWN / XHHW | Insulated conductor types per NEC Table 310.4(A) |
| AWG / kcmil | American wire gauge / thousand circular mils |
| EGC / GEC | Equipment grounding conductor / grounding electrode conductor |
| C / CO | Conduit / conduit only |
Abbreviations with two meanings, MC and AC being the classic cases, are resolved by context and the legend. When reading a full drawing set, check the abbreviation list on the legend sheet before relying on any of these; our guide on how to read electrical drawings covers where legends and general notes sit in a typical set.
Electrical Engineering Abbreviations: Ratings and Quantities
Equipment data sheets and nameplates use an engineering vocabulary that differs between North American and IEC documents.
| Abbreviation | Meaning | Typical use |
|---|---|---|
| V, kV / A, kA | Volts, kilovolts / amperes, kiloamperes | All ratings |
| kVA / kW / kvar | Apparent / real / reactive power | Transformers, loads, capacitors |
| PF | Power factor | Loads, generators |
| FLA / FLC | Full-load amps / full-load current | Motors |
| LRA | Locked-rotor amps | Motor starting |
| MCA / MOCP | Minimum circuit ampacity / maximum overcurrent protection | HVAC nameplates |
| SCCR | Short-circuit current rating | Panels and assemblies, NEC 409 and 440 |
| BIL | Basic impulse insulation level | Transformers, switchgear |
| %Z | Percent impedance | Transformers, fault calculations |
| THD | Total harmonic distortion | Power quality |
| VD | Voltage drop | Cable sizing |
| Ue / Ui / Uimp | Rated operational / insulation / impulse withstand voltage | IEC 60947 devices |
| In / Ir | Rated current / long-time setting | IEC breakers |
| Icu / Ics / Icw | Ultimate / service breaking capacity / short-time withstand | IEC 60947-2 breakers |
| IP / NEMA | Ingress protection (IEC 60529) / NEMA 250 enclosure type | Enclosures |
A North American kAIC rating and an IEC Icu rating express similar ideas but come from different test standards, so they are not directly interchangeable on a specification. Assembly-level ratings, SCCR in North America and the rated conditional or short-time currents under IEC 61439, depend on the combination of devices and busbars, not on the weakest breaker label alone.
Worked Example: Decoding Breaker and Nameplate Labels
Abbreviations become useful when you can turn a label into a design check.
Label 1: switchboard feeder breaker
MCCB 3P 400AF/320AT 65 kAIC @ 480 V, LSI, ST, AUX
- Three-pole molded case breaker, 400 A frame, 320 A trip setting.
- Interrupting rating 65 kA at 480 V.
- Electronic trip with long-time, short-time and instantaneous functions; no ground-fault function.
- Fitted with shunt trip and auxiliary contacts.
If the fault study gives 42 kA at that switchboard bus, the 65 kA rating is adequate: 65 kA ≥ 42 kA. A standard (80%-rated) breaker carries continuous load up to 80% of its trip rating:
Maximum continuous load = 0.80 × 320 A = 256 A
A 100%-rated breaker in a listed assembly could carry the full 320 A continuously. How the 42 kA figure is obtained is explained in the fault current calculation guide.
Label 2: rooftop HVAC unit nameplate
208/230V 3Ø 60 Hz, MCA 28.5 A, MOCP 45 A
- Branch conductors must have ampacity of at least 28.5 A, so 10 AWG copper at a 30 A rating is typical, subject to terminal temperature and conditions of use.
- The overcurrent device may not exceed 45 A; a 40 A or 45 A breaker is acceptable, a 50 A breaker is not.
Both checks follow directly from reading the abbreviations correctly, which is why they belong on panel schedules and submittals.
Next Steps: Using Clear Abbreviations in Switchgear Specifications
Ambiguous abbreviations in an RFQ produce ambiguous quotations. When specifying switchboards, switchgear or substations:
- Include an abbreviation list with the specification and drawings, defining every code used.
- Use full ratings with units:
Icu 50 kA at 415 Vor65 kAIC at 480 V, not just “50k”. - State the standard each rating refers to: IEC 61439, IEC 62271-200, UL 891 or IEEE C37.20.2.
- Use consistent equipment tags across single-line, schedules and nameplates.
- Specify the nameplate and label language and content required on each device.
MARS supplies IEC 61439 LV boards (GGD, GCS, MNS), KYN28 metal-clad switchgear and SF6 ring main units with nameplates and drawings labeled to your tagging convention. Explore the HV and LV switchgear range and send your specification through the quote request form.
Frequently asked questions
What is the abbreviation for breaker?
The common abbreviation for breaker is CB, short for circuit breaker, or BKR on some drawings. More specific abbreviations identify the type: MCB for miniature, MCCB for molded case, ACB for air and VCB for vacuum circuit breakers. On IEC drawings breakers are tagged -Q followed by a number, such as -Q1.
What does PP mean on an electrical panel?
PP on an electrical panel or drawing means power panel, a panelboard that supplies power loads such as motors, HVAC units, receptacles and equipment, as distinct from an LP lighting panel. The name is usually followed by a number and sometimes a floor or voltage code, for example PP-2A or PP-1H.
What does AIC mean on a circuit breaker?
AIC stands for amperes interrupting capacity, often written kAIC in thousands of amperes. It is the maximum short-circuit current the breaker can safely interrupt at a stated voltage, such as 22 kAIC at 240 V. The rating must be equal to or greater than the available fault current where the breaker is installed.
What does AFF mean on electrical drawings?
AFF means above finished floor. It gives the mounting height of a device measured from the finished floor surface to the center or bottom of the device, as stated in the general notes. For example, 18 in AFF for receptacles or 48 in AFF for switches. AFG means above finished grade for outdoor equipment.
What does LSIG mean on a breaker trip unit?
LSIG describes the protection functions of an electronic trip unit: L for long-time overload, S for short-time delay, I for instantaneous and G for ground fault. A trip unit labeled LSI has the first three functions but no ground-fault protection. Each function has its own pickup and delay settings.
What is the difference between MCA and MOCP?
MCA, minimum circuit ampacity, is the smallest conductor ampacity allowed for the equipment's supply circuit. MOCP, maximum overcurrent protection, is the largest fuse or breaker rating permitted by the equipment listing. Both appear on HVAC and refrigeration nameplates, and the installed conductor and breaker must satisfy both values.
Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .
Tags: electrical abbreviations electrical abbreviations list circuit breaker abbreviations breaker box abbreviations electrical engineering abbreviations list


