Switchgear & Substations

Power Distribution Board: MDB, DB Types & Sizing Guide

Open power distribution board with copper busbars and molded-case breakers in an electrical room

Key takeaways

  • A power distribution board hierarchy runs from the main distribution panel at the transformer through sub-main boards to final DBs serving lighting, sockets and equipment.
  • IEC 61439-2 covers power switchgear assemblies, IEC 61439-3 covers boards operated by ordinary persons, while US panelboards follow UL 67 and NEC Article 408.
  • IEC 61439 assumes a rated diversity factor of 0.9 for 2–3 outgoing circuits, falling to 0.6 for 10 or more circuits loaded simultaneously.
  • Incomer current is I = S / (√3 × V); a 630 kVA transformer at 400 V delivers about 909 A, so a 1,000–1,250 A incomer suits.
  • Short-time withstand current Icw must exceed the prospective fault current; a 630 kVA, 6 percent impedance transformer gives roughly 15 kA at its LV terminals.

Quick answer: A power distribution board (DB or distribution panel) is an enclosed assembly of busbars, an incoming device and outgoing circuit breakers that divides one supply into protected circuits. Boards are arranged in a hierarchy: main distribution panel (MDP) at the transformer, sub-main boards per floor or area, and final DBs feeding loads, each sized for current, fault level and diversity.

Every building with more than a handful of circuits relies on a chain of distribution boards between the utility transformer and the loads. Getting that chain right decides whether a fault trips one circuit or the whole site, whether the boards run cool at full load, and whether the system can grow without replacement.

This guide is for consulting engineers, panel builders and procurement teams specifying an electrical distribution board or electrical main distribution panel for commercial, industrial or infrastructure projects. It explains the terminology used in IEC and North American markets, the ratings that matter and a worked sizing example from transformer to incomer.

What Is a Power Distribution Board?

A distribution board is an assembly that receives power from one or more incoming circuits and distributes it to outgoing circuits through protective devices mounted on a common busbar, inside an enclosure. Electrical DB, DB panel, distribution panel board and power distribution panel are regional names for the same thing.

Every board, from a small db box electrical enclosure in an apartment to a 4,000 A main switchboard, contains the same functional parts:

  • Incoming device: main switch-disconnector, MCCB or air circuit breaker (ACB).
  • Busbars: copper or aluminum conductors rated for continuous current and fault withstand.
  • Outgoing devices: MCBs, MCCBs or ACBs, sometimes with RCDs or residual current breakers.
  • Neutral and protective earth bars, sized for harmonic neutral current where non-linear loads dominate.
  • Enclosure with an IP or NEMA rating and internal separation.
  • Metering and control: CTs, meters, surge protective devices and indicator lamps.

An electrical control box differs from a distribution board: control panels hold contactors, PLCs and relays that operate machines, while a DB distributes and protects power. Our electrical control panel guide covers that side. In North America, the line between a panelboard and a switchboard is set by construction and listing; see switchboard vs panelboard for details.

MDP, SMDB and Final DB: What Does MDP Mean in Electrical Design?

MDP stands for main distribution panel: the first board downstream of the utility transformer or service entrance, carrying the full building load. In IEC markets the same board is often called the MDB (main distribution board) or main LV switchboard. Searches for mdp electrical meaning or panel MDP usually come from reading single-line diagrams where these abbreviations appear.

LevelCommon namesTypical ratingDevicesStandard
MainMDP, MDB, main LV switchboard800–6,300 AACB incomer, ACB/MCCB feedersIEC 61439-2, UL 891
Sub-mainSMDB, SDB, distribution panel250–1,600 AMCCB incomer and feedersIEC 61439-2, UL 67 or UL 891
FinalDB, lighting and power panel, consumer unit63–250 AMCB, RCBO, RCCBIEC 61439-3, UL 67
SpecialMCC, essential services board, UPS boardVariesStarters, ATS, static switchesIEC 61439-2, UL 845, UL 1008

The hierarchy keeps fault levels and cable sizes manageable. The MDP sees the highest prospective fault current, so it carries ACBs with high breaking and short-time ratings; final DBs further away see much less fault current, so economical MCBs suffice. Motor-heavy areas get a dedicated motor control center instead of a conventional sub-main. For abbreviations on drawings, keep our electrical abbreviations list to hand.

Which Standards Govern Electrical Distribution Panels?

Two families of standards dominate, and the RFQ should name one clearly.

IEC 61439 series. IEC 61439-1 sets general rules; part 2 covers power switchgear and controlgear assemblies (PSC) such as MDBs and MCCs; part 3 covers distribution boards intended to be operated by ordinary persons (DBO), such as final DBs in offices and homes. The standard requires design verification (temperature rise, short-circuit withstand, dielectric properties, clearances, IP degree, mechanical operation) and routine verification of every assembly. Internal separation is described by Forms 1 to 4, from no separation to full segregation of busbars, functional units and terminals.

North American practice. Panelboards are listed to UL 67 and installed under NEC Article 408; switchboards are listed to UL 891; metal-enclosed switchgear follows UL 1558 and IEEE C37.20.1. NEC 408.36 requires overcurrent protection for each panelboard not exceeding its rating, and NEC 110.26 sets working clearances in front of every board.

Ratings defined by IEC 61439 that belong on every datasheet:

  • InA, rated current of the assembly, and Inc, rated current of each circuit.
  • Icw, rated short-time withstand current, typically for 1 s.
  • Ipk, rated peak withstand current.
  • RDF, rated diversity factor.
  • Rated insulation voltage Ui and impulse withstand voltage Uimp.

For the protective devices inside, see our low-voltage circuit breaker selection guide.

How Do You Size a Distribution Board? Worked Example

Sizing an electrical power distribution board means checking three things: continuous current, short-circuit withstand and diversity. Here is a sub-main and main board check for a light industrial building at 400 V, 50 Hz.

Given: connected load 520 kW, demand factor 0.75 from load analysis, average power factor 0.9. Supply from a dedicated transformer with 6 percent impedance.

  1. Maximum demand: P = 520 × 0.75 = 390 kW; apparent power S = 390 / 0.9 = 433 kVA.
  2. Transformer: choose 630 kVA to give about 30 percent headroom for growth and motor starting.
  3. Incomer current at transformer rating: I = S / (√3 × V) = 630,000 / (1.732 × 400) = 909 A. Select a 1,000 A or 1,250 A ACB and a 1,250 A busbar.
  4. Prospective fault current at LV terminals (infinite source): Isc = I / Z = 909 / 0.06 = 15.2 kA. Specify Icw of at least 25 kA for 1 s, leaving margin for motor contribution and future transformer replacement.
  5. Sub-main feeder for a 200 kW production hall at PF 0.9: I = 200,000 / (1.732 × 400 × 0.9) = 321 A; use a 400 A MCCB.

The same method scales to any board. Use our transformer sizing calculator for the source and the fault current calculation guide when cable impedance between transformer and board must be included.

Diversity, Heat and Busbar Ratings

A distribution panel board is rarely loaded with every circuit at its full rating at once. IEC 61439 recognizes this through the rated diversity factor (RDF), the per-unit value of rated current that outgoing circuits can carry continuously and simultaneously without exceeding temperature-rise limits. Where the manufacturer does not declare a value, the standard assumes:

Number of outgoing circuitsAssumed loading factor
2 and 30.9
4 and 50.8
6 to 90.7
10 and above0.6

That matters for heat. Each MCCB dissipates watts per pole at rated current, and dissipation rises with the square of current. A board where every feeder runs near rating, such as a data center or a process plant with continuous loads, needs an RDF of 1.0 declared and verified, often requiring larger enclosures, ventilated roofs or derated devices.

Practical checks for busbars and heat:

  • Specify busbar rating at the actual ambient; IEC 61439 assumes a 24-hour average of 35 °C.
  • Size the neutral at 100 percent or more where third-harmonic current from LED drivers, IT loads or VFDs is significant.
  • Leave 20 to 25 percent spare ways for future circuits.
  • For runs above about 1,600 A between transformer and MDB, compare cables with bus duct.

Large Electrical Boxes, Enclosures and Forms of Separation

The enclosure is more than a large electrical box. It sets protection against contact, ingress and internal arc propagation. Three parameters should be specified.

Degree of protection. Indoor electrical rooms typically use IP31 to IP42; plant floors with dust or dripping water need IP54; outdoor boards need IP55 or higher, or NEMA Type 3R or 4 in North America. See our NEMA enclosure ratings guide for the US system.

Form of separation.

  • Form 1: no internal separation. Common for small final DBs.
  • Form 2: busbars separated from functional units.
  • Form 3: busbars and each functional unit separated from each other; terminals not separated from their unit.
  • Form 4: as Form 3, plus terminals separated, allowing work on one outgoing circuit while others remain live behind barriers.

Arc containment. IEC TR 61641 testing for internal arcing in LV assemblies, or IEEE C37.20.7 arc-resistant construction for North American switchgear, limits damage and risk to people in front of the board. These options cost more but reduce exposure during operation.

Electrical cabinet box construction, typically 1.5 to 2.0 mm galvanized or painted steel, should match the corrosivity of the site, with stainless steel for coastal and chemical environments.

Next Steps: Specifying and Sourcing Distribution Boards

A distribution board specification that a manufacturer can price accurately has the following:

  1. Single-line diagram with every incomer, feeder, rating and cable size.
  2. System data: voltage, frequency, earthing system (TN-S, TN-C-S, TT, IT), and prospective short-circuit current.
  3. Assembly ratings: InA, Icw for 1 s, Ipk, RDF, Ui and Uimp.
  4. Construction: fixed, plug-in or withdrawable; form of separation; IP or NEMA rating; top or bottom entry; front or rear access.
  5. Metering and communication: meter class and protocol for the BMS.
  6. Testing: routine verification to IEC 61439 and whether you will witness a FAT.

MARS manufactures GGD fixed-type, GCS and MNS withdrawable low-voltage switchboards to IEC 61439, together with the distribution transformers and box-type substations that feed them. Every unit is routine-tested and typical lead time is 25 to 45 days. Explore the HV and LV switchgear range or the compact transformer substations that integrate transformer and MDB in one enclosure, then send your single-line diagram via our quote form. Include the load list and site altitude and ambient temperature, so derating can be checked before the busbar and enclosure are fixed.

Frequently asked questions

What is the difference between a distribution board and a panelboard?

They perform the same function: dividing a supply into protected circuits. Distribution board is the IEC and British term, built to IEC 61439-3 or 61439-2. Panelboard is the North American term for an assembly listed to UL 67 and installed under NEC Article 408, usually rated up to 1,200 A.

What does MDP mean in electrical?

MDP means main distribution panel, the first distribution assembly downstream of the utility transformer or service entrance. It carries the full building load, has the highest fault level in the system, and feeds sub-main distribution boards, motor control centers and large individual loads through breakers or fused switches.

How do I size a power distribution panel?

Calculate maximum demand from connected load and demand factors, convert to current with I = P / (√3 × V × PF) for three-phase, then select the incomer and busbar above that value. Confirm short-time withstand Icw exceeds the prospective fault current and apply the rated diversity factor to outgoing circuits.

What is an electrical DB board?

An electrical DB board is a distribution board: an enclosure with an incoming switch or breaker, busbars, and outgoing miniature or molded-case circuit breakers that feed lighting, socket and equipment circuits. DB is common terminology in the UK, Middle East, India and Southeast Asia.

What is a power distribution box?

A power distribution box is a small enclosed distribution board, often wall-mounted, that splits one feeder into several protected circuits. On construction sites and events the term also describes portable boxes with sockets and breakers, which must meet temporary power rules covered separately in temporary power distribution guides.

How many spare ways should a distribution board have?

Good practice is 20 to 25 percent spare ways, with busbar capacity to match. Spare capacity avoids replacing the board when loads are added. Specify spare ways as equipped (breaker fitted) or space only, because equipped spares cost more but speed up future connections.

Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .

Tags: power distribution board electrical distribution panel distribution board mdp electrical power distribution panel

More guides