
Key takeaways
- Generator kVA equals kW divided by power factor; most three-phase commercial sets are rated at 0.8 PF, so a 200 kW set is a 250 kVA set.
- Three-phase generator current is I = kVA × 1000 / (√3 × V), giving about 301 A for a 250 kVA set at 480 V and 694 A at 208 V.
- Motor starting usually governs sizing: across-the-line starts draw roughly 6 to 7 times running current, and NEMA code letters give locked-rotor kVA per horsepower.
- ISO 8528-1 defines emergency standby, prime, limited-time and continuous ratings; a standby-rated set should not be sized for long daily runtime or peak shaving duty.
- NEC 702.4 requires an optional standby system with automatic transfer to carry the full transferred load unless an approved load management system limits that load.
Quick answer: A generator size calculator adds the running kW of every load that must operate together, adds the extra starting kVA of the largest motor, converts to kVA using power factor (usually 0.8), applies altitude and temperature derating, and then adds 20–25% margin. The result is compared against standby or prime ratings to ISO 8528-1 and the alternator's motor-starting capability.
Undersized generators stall on motor starts, trip on overload or sag voltage until contactors drop out. Oversized generators cost more, run lightly loaded and suffer wet stacking in diesel engines. A disciplined sizing method sits between those failures, and it is the same method whether the answer is a 20 kW home standby set or a 1,000 kW building backup plant.
This guide is for facility engineers, contractors and project buyers who need to check a vendor's proposal or build their own generator size calculator in a spreadsheet. It covers running and starting loads, kW to kVA and amps conversion, a generator size chart, derating, the 300 amp service question, and where batteries, transfer switches and transformers enter the design.
How Do You Calculate What Size Generator You Need?
Generator sizing is the process of matching a generator's continuous kW, kVA and transient capability to the loads it must carry simultaneously, including the worst motor start. A spreadsheet generator kw calculator follows these steps:
- List every load that must run on generator power, with nameplate kW or amps, voltage, phase and power factor.
- Classify the loads as resistive (heaters, incandescent), electronic (drives, UPS, LED drivers) or motor loads (compressors, pumps, fans).
- Sum the running kW and running kVA. Where only amps are known, use
kVA = V × I / 1000for single phase orkVA = √3 × V × I / 1000for three phase. - Identify the largest motor step and calculate its starting kVA from the NEMA code letter or locked-rotor current.
- Check the starting step: running kVA of loads already online plus the starting kVA of the motor being started.
- Apply derating for altitude, ambient temperature and fuel type from the engine manufacturer's data.
- Add margin of 20–25% for growth and to keep the set below its maximum rating.
- Select the rating type (standby or prime) that suits the runtime profile.
The result is two numbers, a continuous kW requirement and a transient starting kVA requirement, and the generator must satisfy both. Electronic loads add a third check: non-linear current distorts generator voltage more than utility voltage because the alternator's subtransient reactance is much higher than a utility source impedance. Projects with large UPS or variable frequency drive loads often specify an oversized alternator on a standard engine for this reason.
Generator kW Calculator: Converting kW, kVA and Amps
Generators carry two ratings. kW is the real power the engine must deliver; kVA is the apparent power the alternator windings must carry. They are linked by power factor, explained in our guide to kVA vs kW:
kVA = kW / PFThree-phase amps: I = kVA × 1000 / (√3 × V)Single-phase amps: I = kVA × 1000 / VkW from amps (three phase): kW = √3 × V × I × PF / 1000
A generator amps calculator is simply the second formula. Three-phase industrial sets are normally rated at 0.8 PF lagging, so the alternator has 25% more kVA than the engine has kW. Single-phase residential sets are usually rated at unity power factor, so their kW and kVA ratings are the same.
The generator amperage you calculate sets the output breaker frame, the feeder conductor size and the transfer switch rating. For a quick cross-check by voltage, see the generator kVA to amps calculator.
Generator size calculator kWh: power versus energy
Generators are sized in kW, not kWh. kWh is energy over time and determines fuel consumption, tank size and runtime, not generator rating. A load of 40 kW for 8 hours uses 320 kWh; the set must still be rated for the 40 kW peak plus any motor start. A generator power consumption calculator therefore answers a fuel question: a diesel set typically consumes in the region of 0.25–0.3 litres per kWh delivered at medium-to-high load, with exact figures taken from the engine fuel curve.
Generator Size Chart: kW, kVA and Amps by Voltage
The generator sizing chart below lists common standby ratings and their full-load current at the most common North American voltages. Three-phase values assume 0.8 PF; single-phase values assume unity PF at 240 V.
| Rating (kW) | kVA at 0.8 PF | Amps 208 V 3-phase | Amps 480 V 3-phase | Amps 240 V 1-phase |
|---|---|---|---|---|
| 20 | 25 | 69 | 30 | 83 |
| 30 | 37.5 | 104 | 45 | 125 |
| 50 | 62.5 | 173 | 75 | 208 |
| 60 | 75 | 208 | 90 | 250 |
| 80 | 100 | 278 | 120 | 333 |
| 100 | 125 | 347 | 150 | 417 |
| 150 | 187.5 | 520 | 226 | 625 |
| 200 | 250 | 694 | 301 | not typical |
| 300 | 375 | 1,041 | 451 | not typical |
| 500 | 625 | 1,735 | 752 | not typical |
| 750 | 937.5 | 2,602 | 1,128 | not typical |
| 1,000 | 1,250 | 3,470 | 1,504 | not typical |
Two patterns stand out. At 208 V the current roughly equals 2.8 A per kVA, so large sets at low voltage need heavy busbar and parallel cable runs. At 480 V the figure falls to about 1.2 A per kVA. Above roughly 1–2 MW, many sites generate at medium voltage or use a generator step-up transformer to reduce cable size; the design considerations are covered in our generator transformer engineering guide.
How Do Motor Starting Loads Affect Generator Sizing?
An induction motor started across the line draws locked-rotor current, typically six to seven times its full-load current, at a low power factor of roughly 0.3–0.4. The generator's voltage dips until the voltage regulator and engine governor recover. If the dip is too deep, contactors chatter, drives trip on undervoltage and the motor may fail to accelerate.
NEMA MG 1 code letters give locked-rotor kVA per horsepower. Common values:
| NEMA code letter | Locked-rotor kVA/hp | Starting kVA, 25 hp motor (mid-range) |
|---|---|---|
| F | 5.0–5.59 | about 133 |
| G | 5.6–6.29 | about 149 |
| H | 6.3–7.09 | about 167 |
| J | 7.1–7.99 | about 189 |
Starting method changes the picture. A wye-delta starter reduces starting kVA to about one third of the direct-on-line value; a soft starter typically limits current to 2.5–4 times full-load; a variable frequency drive starts the motor at close to rated current. The trade-offs are compared in the star-delta starter guide.
Generator manufacturers publish motor starting curves showing the starting kVA (SkVA) the alternator can supply at a given voltage dip, commonly evaluated at 15% or 20%. The design rule is simple: the largest single step of starting kVA, added to the load already running, must fall within the alternator's SkVA at the allowed dip. Sequencing motors in steps with time delays, starting the largest motor first while the set is lightly loaded, often allows a smaller generator than a simultaneous start would require.
Worked Example: Sizing a 480 V Standby Generator
A small commercial building at 480 V three-phase needs standby power for lighting, HVAC and one 40 hp chilled-water pump started across the line (code letter G).
Step 1, running loads:
- Lighting and receptacles: 45 kW at 0.95 PF, giving 47.4 kVA
- HVAC compressors and fans: 60 kW at 0.85 PF, giving 70.6 kVA
- 40 hp pump:
40 × 0.746 / 0.92 efficiency = 32.4 kW; at 0.86 PF this is 37.7 kVA
Running total: 137.4 kW and 155.7 kVA, an aggregate PF of 0.88.
Step 2, starting step: using 6.0 kVA/hp for code G, the pump's starting kVA is 40 × 6.0 = 240 kVA. The other 118 kVA of running load is already online when it starts.
Step 3, margin and rating: 137.4 kW × 1.25 = 172 kW. The next standard size is 200 kW / 250 kVA. Its full-load current is 250,000 / (1.732 × 480) = 301 A, so a 400 A transfer switch and output breaker are typical.
Step 4, verify: the selected set's published SkVA at 20% dip must exceed 240 kVA. If it does not, either specify a larger alternator, add a soft starter or start the pump first. Fitting a soft starter limiting current to 3 × FLA reduces the step to roughly 115–130 kVA, comfortably inside a 250 kVA alternator's capability.
Final current also drives feeder size and equipment grounding conductor selection; see the wire size calculator guide.
What Size Generator for a 300 Amp Service?
A 300 amp, 120/240 V single-phase service has a theoretical capacity of 300 × 240 = 72 kVA. Very few homes ever approach that figure. The service rating reflects the NEC Article 220 calculated load plus headroom; actual peak demand is often 30–60% of the service rating.
The practical options are:
- Whole-house automatic standby without load management: NEC 702.4 requires the generator to carry the full load that will be transferred, calculated per Article 220. For a large home this may land at 45–60 kW.
- Whole-house with load management: load shedding modules hold off large appliances such as air conditioners, ranges and EV chargers until capacity is available, which commonly allows a 22–30 kW air-cooled set.
- Essential circuits only: a separate critical-load panel fed through a transfer switch, often 10–20 kW.
For the transfer switch side of the decision, read the automatic transfer switch guide and the transfer switch types and sizing article. A 300 A service typically needs a 300 A or 400 A service-rated transfer switch for whole-house transfer.
Battery systems change this calculation. A battery paired with a smaller generator can supply short peaks while the generator covers average energy, a configuration explained in hybrid generator battery systems. Work on service equipment, transfer switches and generator connections must follow local code and be carried out by a licensed electrician.
Derating, Rating Types and Common Sizing Mistakes
ISO 8528-1 defines the rating classes that vendors quote:
- Emergency standby power (ESP): variable load during utility outages, limited annual hours, no overload capability.
- Prime power (PRP): unlimited hours at variable load, with an average load limit over a 24-hour period, commonly 70% of the prime rating.
- Limited-time running power (LTP): constant load for a limited number of hours per year.
- Continuous operating power (COP): constant load for unlimited hours.
The standby rating is typically about 10% higher than the prime rating of the same set. A set used for peak shaving or as the main source at a remote site needs a prime or continuous rating.
Derating is required above the engine's rated altitude and ambient. Typical engine data show derating somewhere in the range of 1–4% per 300 m above 1,000–1,500 m and a few percent per 5 °C above 25–40 °C; use the specific engine curve, not a generic rule. Natural gas engines generally derate more than diesel.
Common mistakes to avoid:
- Ignoring the starting step of the largest motor or a fire pump.
- Sizing for kW at 0.8 PF when the load is 0.7 PF.
- Running a diesel set below 30% load for long periods, which causes wet stacking.
- Forgetting harmonic distortion from UPS and drive loads.
Next Steps: Specifying and Sourcing Generator Interconnection Equipment
Once the generator kW and kVA are fixed, the rest of the power path has to match it. A clear RFQ package should include:
- Load schedule with running kW, kVA, power factor and starting method of each motor
- Required rating type (ESP, PRP or COP) and annual runtime
- Site altitude, maximum ambient and enclosure or sound requirements
- Allowed voltage and frequency dip on the largest step load
- Output voltage, grounding method and whether generation is at LV or MV
- Transfer scheme: open transition, closed transition or paralleling with the utility
Medium and large standby plants often connect through a generator step-up transformer, medium-voltage switchgear and a packaged substation. MARS supplies oil-immersed and dry-type transformers, KYN28 metal-clad switchgear, IEC 61439 LV switchboards and compact transformer substations built to IEC 60076 and IEC 62271, with routine tests on every unit and FAT on request. Where the project would benefit from shaving generator runtime or covering the transfer gap, MARS liquid-cooled C&I cabinets and containerised BESS from the energy storage system range can be integrated.
Send your single-line diagram and load schedule through the quote request page for a transformer and switchgear proposal sized to your generator.
Frequently asked questions
How do I calculate what size generator I need?
Add the running kW of all loads that operate together, convert to kVA using each load's power factor, then add the starting kVA of the largest motor as a separate transient check. Apply altitude and temperature derating and add 20 to 25 percent margin. Select a generator whose kW, kVA and motor-starting capability all exceed these results.
What size generator do I need for a 300 amp service?
It depends on calculated load, not service size. A 300 A, 240 V service can supply 72 kVA, but most homes peak far lower. Without load management, NEC 702.4 requires sizing to the full transferred load, often 45 to 60 kW. With load shedding, a 22 to 30 kW set is common. Essential-circuit systems may need only 10 to 20 kW.
How many amps does a 100 kW generator produce?
A 100 kW three-phase generator rated at 0.8 power factor is 125 kVA. Using I = kVA × 1000 / (√3 × V), it delivers about 347 A at 208 V and about 150 A at 480 V. A 100 kW single-phase generator at unity power factor and 240 V delivers about 417 A.
Is generator size measured in kW or kWh?
Generator capacity is measured in kW and kVA, which is instantaneous power. kWh is energy and determines fuel consumption and runtime. A generator supplying 50 kW for 10 hours delivers 500 kWh, but its rating must still cover the 50 kW peak plus any motor starting surge.
How much bigger should a generator be than the load?
A margin of 20 to 25 percent above the calculated running load is typical for standby sets, which keeps the engine below maximum output and allows modest load growth. The motor starting check is separate: the largest starting step must fit within the alternator's published starting kVA at the allowed voltage dip.
What power factor is used for generator sizing?
Three-phase commercial and industrial generators are usually rated at 0.8 power factor lagging, so kVA is 1.25 times kW. Single-phase residential generators are typically rated at unity power factor. If the actual load power factor is lower than the rating, the alternator kVA, not engine kW, limits the usable output.
Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .
Tags: generator size calculator generator sizing generator size chart generator kw calculator generator amps calculator


