Transformers

Delta to Wye Conversion: Formulas, Examples & Transformers

Delta-wye distribution transformer in a test bay used for delta to wye conversion

Key takeaways

  • For balanced loads Z_Y = Z_Δ / 3 and Z_Δ = 3 × Z_Y, so a 30 Ω delta resistor bank behaves exactly like a 10 Ω wye bank.
  • Unbalanced delta to wye conversion uses Z_a = Z_ab·Z_ca / ΣZ; the reverse wye to delta uses Z_ab = (Z_aZ_b + Z_bZ_c + Z_cZ_a) / Z_c.
  • Wye phase voltage equals delta line voltage divided by √3 and lags it by 30°, giving 277 V from 480 V and 120 V from 208 V.
  • Delta winding current is line current divided by √3; a 1,000 kVA, 13.8 kV delta primary carries 41.8 A per line but only 24.2 A per winding.
  • Converting a building from 240 V delta to 208Y/120 V service changes motor and heater voltages by 13%, so every three-phase load must be reviewed.

Quick answer: Delta to wye conversion replaces three delta impedances with an equivalent star: each wye arm equals the product of the two adjacent delta impedances divided by the sum of all three, Z_a = Z_ab × Z_ca / (Z_ab + Z_bc + Z_ca). For a balanced load this simplifies to Z_Y = Z_Δ / 3. Wye voltage equals line voltage divided by √3, shifted 30°.

The phrase delta to wye conversion covers two related tasks. In circuit analysis it means transforming three impedances connected in a triangle into an equivalent star, the Kennelly or Δ-Y transformation, so that a bridge or a three-phase load can be solved with simple series-parallel rules. In power systems it also means converting phasor voltages and currents between line and phase quantities, and sometimes physically converting an installation from a delta service to a wye service.

This article treats all three for engineers, students and facility planners. It gives the formulas in both directions, works through balanced and unbalanced examples, shows how to calculate transformer winding currents, and closes with the practical checklist for re-supplying a site from a new delta-wye transformer.

What Is Delta to Wye Conversion?

A delta to wye conversion is a mathematical substitution that replaces a delta network of three impedances with a wye network that presents the same impedance between every pair of terminals. Seen from terminals a, b and c, the two networks are indistinguishable, so any current or voltage outside them is unchanged.

The transformation is needed whenever impedances are neither purely in series nor in parallel. Classic cases are a Wheatstone bridge, an unbalanced three-phase load fed by a three-wire supply, a transformer equivalent circuit in a fault study, and a network of cable and source impedances in a short-circuit calculation.

Notation used here

  • Delta impedances are named by the terminals they join: Z_ab, Z_bc, Z_ca.
  • Wye impedances are named by the terminal they connect to: Z_a, Z_b, Z_c, all meeting at the star point n.
  • Impedances may be resistances, reactances or complex values; the formulas work identically with complex arithmetic.

The same algebra applies to the physical windings of transformers and motors, whose voltage and current relationships are described in the companion star and delta connection guide. Here the focus is on the conversion itself and how to calculate with it.

Delta to Wye and Wye to Delta Formulas

Let ΣZ = Z_ab + Z_bc + Z_ca. Each wye arm equals the product of the two delta impedances touching its terminal, divided by the sum.

ConversionFormulaMemory aid
Δ to Y, arm aZ_a = Z_ab × Z_ca / ΣZProduct of adjacent sides over sum
Δ to Y, arm bZ_b = Z_ab × Z_bc / ΣZAdjacent to terminal b
Δ to Y, arm cZ_c = Z_bc × Z_ca / ΣZAdjacent to terminal c
Y to Δ, side abZ_ab = (Z_aZ_b + Z_bZ_c + Z_cZ_a) / Z_cSum of pair products over opposite arm
Y to Δ, side bcZ_bc = (Z_aZ_b + Z_bZ_c + Z_cZ_a) / Z_aOpposite arm is a
Y to Δ, side caZ_ca = (Z_aZ_b + Z_bZ_c + Z_cZ_a) / Z_bOpposite arm is b
BalancedZ_Y = Z_Δ / 3, Z_Δ = 3 × Z_YFactor of three

Admittance users can write the wye to delta direction more compactly: Y_ab = Y_a × Y_b / (Y_a + Y_b + Y_c), which mirrors the delta to wye impedance form. That symmetry is a useful self-check when deriving by hand.

The balanced case explains a frequently quoted fact: a delta-connected heater bank draws three times the power of the same elements reconnected in wye on the same supply, because each element sees √3 times the voltage, giving three times the power per element.

Worked Delta Wye Calculations: Balanced and Unbalanced

Example 1: balanced resistive load on 480 V

Three 30 Ω heater elements are connected in delta on a 480 V, three-phase supply. Equivalent wye: Z_Y = 30 / 3 = 10 Ω. Wye phase voltage: 480 / √3 = 277 V. Line current: 277 / 10 = 27.7 A.

Check directly in delta: each element carries 480 / 30 = 16 A; line current is 16 × √3 = 27.7 A. Power is √3 × 480 × 27.7 ≈ 23.0 kW, which equals 3 × 16² × 30 = 23.0 kW. Both methods agree.

Example 2: unbalanced delta

Let Z_ab = 10 Ω, Z_bc = 20 Ω, Z_ca = 30 Ω, so ΣZ = 60 Ω.

  • Z_a = 10 × 30 / 60 = 5.0 Ω
  • Z_b = 10 × 20 / 60 = 3.33 Ω
  • Z_c = 20 × 30 / 60 = 10.0 Ω

Reverse check: pair-product sum = 5 × 3.33 + 3.33 × 10 + 10 × 5 = 100. Then Z_ab = 100 / 10 = 10 Ω, Z_bc = 100 / 5 = 20 Ω, Z_ca = 100 / 3.33 = 30 Ω. The original network is recovered, confirming the arithmetic.

Notice the smallest wye arm sits at terminal b, which touches the two smallest delta sides. A quick sanity test is that every wye arm must be smaller than either adjacent delta side. If it is not, an index has been swapped.

With complex impedances, keep the values in rectangular form for addition and polar form for multiplication and division, and convert carefully; most errors in transformer and fault studies come from mixing the two.

Converting Current and Voltage from Delta to Wye

Phasor quantities convert with a magnitude factor of √3 and a 30° rotation. For a positive-sequence (ABC) system:

  • Voltage: V_an = (V_ab / √3) ∠ −30°. The phase voltage lags the corresponding line voltage by 30°.
  • Current: I_a = √3 × I_ab ∠ −30°. The line current lags the delta branch current by 30°.

For negative sequence the angle reverses to +30°, which is why phase rotation matters in protection and metering, as discussed in the phase rotation guide.

Line voltage (delta)Phase voltage (wye)Typical system
208 V120 VNorth American commercial
400 V231 VIEC low voltage (400/230 V)
480 V277 VNorth American industrial
600 V347 VCanadian industrial
13.8 kV7.97 kVMV distribution
34.5 kV19.9 kVMV distribution and collector

These values describe the same three-phase system viewed two ways. A 480 V delta system has no 277 V available unless a wye winding with a neutral is provided, which is the job of a delta-wye transformer. Details of North American line and phase voltage pairs are in three-phase line-to-line voltage.

Delta to Wye Transformer Calculator Method

A delta to wye transformer calculator needs only kVA and voltages. Line current on either side is I_L = S / (√3 × V_L). Winding current is then the line current in a wye winding, or line current divided by √3 in a delta winding.

Worked example: 1,000 kVA, 13.8 kV Δ to 480Y/277 V

  1. HV line current: 1,000,000 / (1.732 × 13,800) = 41.8 A.
  2. HV winding current (delta): 41.8 / 1.732 = 24.2 A.
  3. LV line current: 1,000,000 / (1.732 × 480) = 1,203 A, equal to the LV winding current (wye).
  4. Turns ratio per phase: delta winding voltage 13,800 V over wye winding voltage 277 V, which is 49.8 : 1.
  5. Check: 24.2 × 49.8 ≈ 1,205 A, matching the LV winding current within rounding.

The turns ratio of a Dy transformer is not the line voltage ratio of 28.75 but √3 times it, because the HV winding sees line voltage while the LV winding sees phase voltage. Turns ratio testers measure per winding, so expect 49.8 on this unit when testing to IEC 60076-1 or IEEE C57.12.90.

For quick sizing from load data, the transformer sizing calculator returns kVA and line currents; for a deeper look at winding arrangement and phase shift, see the delta-Y transformer guide.

How Do You Convert from Delta to Wye Service in a Building?

Older plants and commercial buildings often run on 240 V delta, sometimes with a high-leg center tap, or on 480 V ungrounded delta. Converting to a 208Y/120 V or 480Y/277 V solidly grounded wye supply gives a neutral for single-phase loads and makes ground faults easy to detect and clear. It is a system change, not a rewiring trick, and it must be engineered.

  1. Survey loads. List every three-phase motor, heater and drive with its nameplate voltage. Equipment rated 230 V on a 208 V supply sees a 9.6% shortfall; 240 V heaters lose about 25% of their output at 208 V because power scales with voltage squared.
  2. Select the transformer. Typically a Dyn1 or Dyn11 unit sized for the existing peak demand plus growth, with taps to correct for low utility voltage.
  3. Establish grounding. Bond the new wye neutral at the service or transformer per NEC 250.24 or 250.30, size the grounding electrode conductor, and remove any old corner-ground bonds.
  4. Re-mark conductors. High-leg (orange) identification no longer applies; phase and neutral color codes must follow the new system.
  5. Review protection. Ground-fault protection of equipment is required on 480Y/277 V services of 1,000 A and above under NEC 230.95.
  6. Commission. Verify phase rotation, voltages and neutral bonding before reconnecting loads.

The high-leg arrangement being replaced is explained in the high-leg delta transformer article; the voltage trade-offs are compared in 208 vs 240 volts.

Where Engineers Use Delta-Wye Conversions

Beyond textbook bridges, the transformation appears throughout routine power engineering:

  • Short-circuit studies. Source, transformer and cable impedances are reduced to a per-phase wye equivalent before applying I_sc = V_ph / Z_total. Delta-connected capacitor banks and motor loads are converted the same way.
  • Unbalanced load analysis. A three-wire delta load with unequal branches is converted to wye, then the floating star-point voltage is solved by Millman's theorem to find each line current.
  • Zero-sequence networks. A delta winding blocks zero-sequence current from passing between systems but allows it to circulate internally, so in a fault model the delta side of a Dyn transformer appears open to zero sequence while the grounded wye side connects to the reference.
  • Harmonic filters and capacitor banks. A delta bank of capacitance C per leg is equivalent to a wye bank of 3C per leg; kvar ratings must be compared at the correct voltage.
  • Metering and CT connections. On differential protection of a Dy transformer, CTs or relay software apply the inverse 30° shift so that through current balances.

For the power quantities that flow once the circuit is solved, including kVA, kW and kvar per phase and total, see apparent, reactive and real power.

Next Steps: Specifying and Sourcing

If your calculation leads to a new delta-wye transformer, the RFQ should give the supplier enough to design it correctly the first time:

  • Rated kVA and any future expansion, with load profile or demand data.
  • Primary voltage, connection and BIL; secondary voltage as line and phase values, for example 480Y/277 V.
  • Vector group (Dyn1 for many North American specs, Dyn11 for IEC) and whether parallel operation is required.
  • Neutral current rating, especially with nonlinear single-phase loads that add triplen harmonics.
  • Tap range, impedance target and loss evaluation basis.
  • Installation type: indoor, pad-mounted, substation, and the applicable standard, IEC 60076 or IEEE C57.12.00.

MARS manufactures oil-immersed distribution transformers and pad-mounted transformers with delta primaries and grounded wye secondaries in 50 and 60 Hz versions, routine tested on every unit. Share your voltages and load list on the request a quote page for a technical offer.

Frequently asked questions

How do you convert delta to wye?

For each wye arm, multiply the two delta impedances connected to that terminal and divide by the sum of all three delta impedances. For example, Z_a equals Z_ab times Z_ca divided by Z_ab plus Z_bc plus Z_ca. When all delta impedances are equal, each wye impedance is simply one third of the delta value.

What is the formula for wye to delta conversion?

Add the three pair products of the wye arms, Z_a·Z_b plus Z_b·Z_c plus Z_c·Z_a, then divide by the wye arm opposite the delta side being calculated. Z_ab uses Z_c as divisor, Z_bc uses Z_a and Z_ca uses Z_b. For balanced networks the delta impedance is three times the wye impedance.

Why divide by 3 in delta to wye conversion?

With equal impedances Z in each delta side, the formula becomes Z times Z divided by 3Z, which equals Z/3. Physically, each wye arm sees only phase voltage, which is line voltage over √3, and carries line current, so it needs one third of the impedance to draw the same power.

How do I convert line voltage to phase voltage?

In a balanced three-phase wye system, phase voltage equals line voltage divided by 1.732. A 480 V system gives 277 V line to neutral; 208 V gives 120 V; 400 V gives 231 V. In a delta system, the voltage across each winding equals the line voltage, and there is no neutral unless one is derived.

Can I convert a 240 V delta service to 208Y/120 V?

Yes, by replacing the supply transformer or adding a delta-wye transformer, but every three-phase load must be checked because voltage falls by about 13%. Heaters lose about a quarter of their output and some 240 V motors may run hot. Grounding, neutral sizing and conductor identification must also be updated by a licensed electrician.

Is the turns ratio of a delta-wye transformer the same as its voltage ratio?

No. The HV delta winding sees line voltage while the LV wye winding sees phase voltage, so the per-winding turns ratio is the line voltage ratio multiplied by √3. A 13,800 to 480Y/277 V Dy transformer has a 28.75 voltage ratio but a 49.8 turns ratio.

Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .

Tags: delta to wye conversion convert from delta to wye delta to wye and wye to delta delta wye calculations delta to wye transformer calculator

More guides