
Key takeaways
- Primary current is I = kVA × 1000 / (√3 × V) for three-phase; a 75 kVA, 480 V transformer draws 90.2 A and takes a 125 A primary-only fuse.
- NEC Table 450.3(B) allows 125% primary-only protection, or 250% primary with secondary protection at 125% for transformers rated 1000 V or less.
- NEC Table 450.3(A) allows MV primary fuses up to 300% of rated current for transformers over 1000 V with impedance up to 10%.
- Fuses must withstand energizing inrush, commonly 12 times full-load current for 0.1 s, without melting or degrading.
- MV fuses follow ANSI C37.46 E-ratings or IEC 60282-1; switch-fuse combinations for transformer protection are covered by IEC 62271-105.
Quick answer: Transformer fuse size is set by NEC 450.3: for transformers 1000 V and below, a primary-only fuse may be up to 125% of rated primary current (next standard size up when 9 A or more), or up to 250% when secondary protection at 125% is also provided. Above 1000 V, primary fuses may reach 300%. The fuse must also ride through inrush and protect the transformer damage curve.
Choosing a transformer fuse looks like simple arithmetic: find rated current, multiply by a percentage, pick the next standard size. In reality the fuse has three jobs that pull in different directions. It must stay intact during inrush and normal overload, it must clear faults before the transformer is damaged, and it must coordinate with the protection above and below it.
This guide is for electrical engineers, contractors and maintenance staff sizing fuses for LV dry-type and MV distribution transformers. It covers the NEC 450.3 rules, a ready fuse sizing chart for transformers at 480 V, MV fuse selection for pad-mounted units and ring main units, and worked examples. Work on service and distribution equipment must follow local code and be carried out by qualified, licensed personnel.
How to Calculate Transformer Primary and Secondary Current
Every transformer fuse sizing calculation begins with rated current:
- Three-phase:
I = kVA × 1,000 / (√3 × VLL) - Single-phase:
I = kVA × 1,000 / V
Use nameplate kVA and the rated voltage of the winding being protected, not the measured load. Our full load amps calculator guide lists values for common sizes and voltages.
A simple transformer primary fuse size calculator follows five steps:
- Find rated primary current from kVA and primary voltage.
- Choose the protection method: primary-only, or primary plus secondary.
- Apply the NEC 450.3 percentage for that method and voltage class to get the maximum rating.
- Round to a standard fuse size from NEC 240.6(A): 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600 A and up. Round up only where the code note permits; otherwise round down.
- Check inrush and coordination: confirm the fuse minimum-melt curve passes 12 × FLA at 0.1 s and sits below the transformer damage curve.
Note that NEC 450.3 sets the maximum rating. A smaller fuse is permitted if it does not blow on inrush or normal load. Conductors still need their own protection under Article 240, which may further limit the fuse.
NEC 450.3(B): Transformers 1000 Volts and Below
For LV transformers, including the dry-type units that feed 208Y/120 V and 120/240 V panels, NEC Table 450.3(B) gives two methods. The threshold is 1000 V in the 2023 NEC; earlier editions used 600 V.
| Protection method | Primary current | Max primary fuse | Secondary current | Max secondary fuse |
|---|---|---|---|---|
| Primary only | 9 A or more | 125% (next higher standard size permitted) | Not required by 450.3 | |
| Primary only | 2 A to under 9 A | 167% | Not required by 450.3 | |
| Primary only | Under 2 A | 300% | Not required by 450.3 | |
| Primary and secondary | Any | 250% | 9 A or more | 125% (next higher permitted) |
| Primary and secondary | Any | 250% | Under 9 A | 167% |
The primary-and-secondary method is useful when the 125% primary fuse would blow on inrush, which can happen with small, low-impedance or toroidal transformers. It lets the primary fuse be sized up to 250%, with the secondary main providing overload protection.
Even with primary-only protection under 450.3, the secondary conductors must comply with NEC 240.21(C) tap rules. For two-wire single-phase and three-wire delta-delta secondaries, primary protection can protect secondary conductors if it is sized by the ratio; for typical delta-wye 480 V to 208Y/120 V units, a secondary main overcurrent device is almost always needed. See our transformer overcurrent protection guide for these conductor rules and breaker settings.
Transformer Fuse Size Chart for 480 V Three-Phase Units
This transformer fuse size chart applies NEC 450.3(B) primary-only protection (125%, next standard size up) to common three-phase dry-type transformers on a 480 V primary. It is a starting point; check inrush, conductor ampacity and the manufacturer's recommendations. For breaker equivalents see our transformer breaker size chart.
| kVA (3-phase) | Primary FLA at 480 V | 125% value | Max primary-only fuse | Secondary FLA at 208 V |
|---|---|---|---|---|
| 15 | 18.0 A | 22.6 A | 25 A | 41.6 A |
| 30 | 36.1 A | 45.1 A | 50 A | 83.3 A |
| 45 | 54.1 A | 67.7 A | 70 A | 124.9 A |
| 75 | 90.2 A | 112.8 A | 125 A | 208.2 A |
| 112.5 | 135.3 A | 169.1 A | 175 A | 312.3 A |
| 150 | 180.4 A | 225.5 A | 250 A | 416.4 A |
| 225 | 270.6 A | 338.3 A | 350 A | 624.5 A |
| 300 | 360.8 A | 451.0 A | 500 A | 832.7 A |
For single-phase transformers use I = kVA × 1,000 / V. For example, a 25 kVA single-phase unit on 480 V draws 52.1 A; 125% is 65.1 A, so the maximum primary-only fuse is 70 A. Our 30 kVA transformer guide works through the full feeder design for that popular size.
Use time-delay, current-limiting fuses (for example UL Class J or RK1 time-delay types) on transformer primaries. Fast-acting fuses sized at 125% are very likely to open on energization, and nuisance replacements with oversized fuses are a common field error.
Worked Example: 75 kVA 480–208Y/120 V Transformer
A 75 kVA, three-phase, 480 V delta to 208Y/120 V dry-type transformer feeds a lighting and receptacle panel. Compare both NEC 450.3(B) methods.
Rated currents.
- Primary:
75,000 / (1.732 × 480) = 90.2 A - Secondary:
75,000 / (1.732 × 208) = 208.2 A
Method 1, primary only. 90.2 × 1.25 = 112.8 A. The next higher standard size is permitted, so the maximum is 125 A. Because this is a delta-wye transformer, the secondary conductors still need protection at their termination under 240.21(C), typically a 225 A or 250 A main breaker or fused switch at the panel, sized to the conductor ampacity.
Method 2, primary and secondary. Primary maximum 90.2 × 2.5 = 225.5 A, so 225 A (rounding up is not permitted for the 250% value). Secondary maximum 208.2 × 1.25 = 260 A, next higher standard 300 A, provided secondary conductors are rated for it.
Inrush check. Using 12 × FLA for 0.1 s: 12 × 90.2 = 1,082 A. A 125 A Class J time-delay fuse typically has a melting time well above 0.1 s at about 8.7 times its rating, so it should hold, but confirm on the fuse curve. If it does not, Method 2 allows a larger primary fuse.
Fault check. With 5% impedance, secondary bolted fault is 208.2 / 0.05 = 4,164 A, reflected to the primary as 4,164 × 208 / 480 = 1,804 A. The primary fuse must clear this within the transformer's IEEE C57.12.01/C57.109 through-fault capability.
Medium-Voltage Transformer Fuses (Over 1000 V)
NEC Table 450.3(A) covers transformers over 1000 V. For an unsupervised location with secondary protection at 125%, the maximum primary fuse is 300% of rated current for impedances up to 10%. Supervised locations, where qualified persons monitor and service the installation, allow primary-only protection with a 250% fuse.
| Location and impedance | Primary fuse max | Secondary over 1000 V, fuse max | Secondary 1000 V or less |
|---|---|---|---|
| Any location, Z ≤ 6% | 300% | 250% | 125% |
| Any location, 6% < Z ≤ 10% | 300% | 225% | 125% |
| Supervised, primary only | 250% | Not required | Not required |
| Supervised, Z ≤ 10%, with secondary | 300% | 225–250% | 250% |
In practice MV fuses are chosen well below these maxima. North American MV power fuses carry E-ratings under ANSI C37.46; distribution fuse links on pole-mounted and pad-mounted transformers use K or T speed links or bayonet-type expulsion fuses backed by current-limiting fuses. In IEC markets, HV fuses follow IEC 60282-1 and are applied in switch-fuse combinations to IEC 62271-105, typically in ring main units.
Example: a 1,500 kVA pad-mounted transformer at 12.47 kV has FLA = 1,500,000 / (1.732 × 12,470) = 69.4 A. The NEC maximum is 3 × 69.4 = 208 A, but selection is driven by inrush (12 × 69.4 = 833 A at 0.1 s), cold-load pickup and the damage curve, usually giving a fuse somewhere around 1.5–2 times FLA. Our 3 phase pad mounted transformer guide explains loop-feed fusing arrangements.
Fuse Sizing Chart for Transformers on 11 kV RMUs
For IEC distribution networks, the following fuse sizing chart for transformers shows indicative HV backup fuse ratings for 11 kV, 3-phase transformers protected by a ring main unit switch-fuse combination. Values vary by fuse manufacturer, transformer impedance and network practice; always use the fuse manufacturer's selection table and check against IEC 62271-105 transfer current requirements.
| Transformer kVA | Rated current at 11 kV | Indicative fuse rating |
|---|---|---|
| 100 | 5.2 A | 10–16 A |
| 250 | 13.1 A | 25 A |
| 400 | 21.0 A | 40 A |
| 630 | 33.1 A | 50–63 A |
| 800 | 42.0 A | 63–80 A |
| 1000 | 52.5 A | 80–100 A |
| 1250 | 65.6 A | 100–125 A |
Two constraints drive these ratios of roughly 1.5–2 times rated current. The fuse must not melt on inrush or permissible overload, and it must clear an LV terminal fault fast enough, with the RMU switch handling the transfer current where the fuse and switch share the job. Above about 1,250–1,600 kVA many utilities move from fuses to a circuit breaker with relay protection. Our comparison of ring main units vs metal-clad switchgear discusses that transition, and the transformer inrush current guide explains the inrush constraint. When replacing a transformer with a different kVA or impedance, recheck the fuse rating rather than reusing the old one.
Next Steps: Specifying and Sourcing
To specify transformer fuses and protection correctly, collect and share:
- Transformer kVA, primary and secondary voltages, connection and percent impedance from the nameplate or data sheet.
- Source fault level at the primary and the protection device upstream.
- Whether the location is supervised under NEC definitions, and which code edition applies.
- Required fuse class or type: UL Class J/RK1 at LV, E-rated or current-limiting at MV, or IEC 60282-1 backup fuses in RMUs.
- Through-fault damage curve and inrush data from the transformer manufacturer.
MARS manufactures oil-immersed transformers and pad-mounted transformers (state the required fusing arrangement in the RFQ), cast-resin dry-type transformers and SF6 ring main units to IEC 62271, plus ANSI/IEEE variants. Impedance and through-fault data can be provided for your protection study, every unit is routine-tested, FAT is welcome and typical lead time is 25–45 days. Request a matched transformer and switchgear offer through the quote page.
Sourcing the transformer and its primary switchgear together simplifies coordination: one supplier confirms that the fuse rating, inrush characteristic and through-fault capability work as a set, and the FAT can verify the combination before shipment.
Frequently asked questions
What size fuse do I need for a 75 kVA transformer?
A 75 kVA, three-phase transformer on 480 V draws 90.2 A on the primary. Under NEC 450.3(B) primary-only protection, 125% gives 112.8 A, so the maximum is a 125 A fuse. If secondary protection at 125% is provided, the primary fuse may be up to 250%, or 225 A. Use time-delay current-limiting fuses and verify inrush and conductor ampacity.
How do you size a fuse for a transformer primary?
Calculate rated primary current as kVA × 1000 divided by voltage, or by √3 × voltage for three-phase. Apply the NEC 450.3 percentage: 125% primary-only or 250% with secondary protection at 1000 V and below, up to 300% above 1000 V. Round to a standard size where permitted, then confirm the fuse withstands inrush and protects the damage curve.
Why do transformer fuses blow when energizing?
Transformer fuses blow on energization when inrush current exceeds the fuse's melting characteristic. Inrush can reach about 12 times full-load current for 0.1 seconds, or more for small transformers. Fast-acting fuses or fuses sized very close to rated current are the usual cause. Use time-delay fuses or the NEC primary-and-secondary method, which permits a larger primary fuse.
Do I need secondary protection on a transformer?
NEC 450.3(B) does not require secondary protection if the primary is protected at 125%, but secondary conductors must still be protected under NEC 240.21(C). For typical delta-wye transformers such as 480 V to 208Y/120 V, that usually means a secondary main breaker or fused switch at the panel served. Secondary protection also lets the primary fuse be larger.
What is an E-rated fuse?
An E-rated fuse is a medium-voltage power fuse rated under ANSI C37.46 with a defined melting characteristic. Fuses rated 100E or below must melt in 300 seconds at between 200% and 240% of the E rating; above 100E, the melting time is 600 seconds at 220% to 264%. E-rated fuses are common on MV transformer primaries in North America.
Can I use a smaller fuse than NEC 450.3 allows?
Yes. NEC 450.3 sets maximum ratings, not minimums. A smaller fuse gives better transformer protection, provided it does not open on energizing inrush, cold-load pickup or normal permissible overload, and coordinates with downstream devices. Check the fuse minimum-melt curve against the inrush point and the expected load profile before reducing the rating.
Written and reviewed by the MARS application engineering team in Shanghai, who specify and test transformers, switchgear, substations and battery storage for projects in 40+ countries. Last updated .
Tags: transformer fuse size transformer fuse sizing transformer fuse size chart transformer primary fuse size calculator transformer fuses


